Why is my Emerson UPS showing 'Battery Cabinet Not Connected'?
If your Emerson UPS displays 'Battery Cabinet Not Connected', it means the power cable of the external battery cabinet is not connected or fully inserted. Connect the cable.
How to clear Power Module Redundancy Alarm on Emerson Liebert APS?
If your Emerson UPS shows 'Power Module Redundancy Alarm', it means the UPS has no redundant power module. Add power modules or replace the faulty power module to obtain redundancy.
What to do if I see a Low Battery Warning on my Emerson Liebert APS?
If the Emerson UPS indicates 'Low Battery Warning', this means the battery capacity has reached the user programmable set point. Check the upstream feeder breaker or the UPS input breaker and reset if necessary. If the problem persists, initiate an orderly shutdown of all connected equipment as a UPS shutdown is imminent.
How to fix 'No Matching Module' error on Emerson Liebert APS?
If your Emerson UPS displays 'No Matching Module', it means only one battery module is inserted into one layer of bays in the system. Ensure that there are a pair of battery modules in the same layer of the frame.
What does Transformer Temperature Warning mean on my Emerson Liebert APS?
If your Emerson UPS is showing 'Transformer Temperature Warning', it means a high temperature condition has occurred in the output transformer area. Check the air filters located behind the bezels and clean them if necessary, or check to see if the ambient temperature is too high. If the problem persists, contact your local Liebert Service representative.
Why does my Emerson Liebert APS say 'Insufficient Capacity To Start Inverter'?
If your Emerson UPS displays 'Insufficient Capacity To Start Inverter', it indicates that the load value exceeds the maximum load capacity of all operating modules. Ensure all power modules are inserted and the locking lever is fully inserted. If all modules are active, add power modules to increase capacity.
What to do if Emerson UPS says 'No Battery Modules Are Ready'?
If the Emerson UPS displays 'No Battery Modules Are Ready', it indicates that the battery module is not ready, and the yellow fault LED is flashing. Ensure that the battery module is fully inserted and the locking levers are in the locked position. If the problem continues, contact your local Liebert Service representative.
What does 'Battery Test Warning Weak Battery' mean on my Emerson UPS, and what should I do?
If your Emerson UPS shows a 'Battery Test Warning Weak Battery' message, it means one or more battery modules has detected batteries that are no longer in specification due to age or operating conditions. Replace the battery string.
What causes BM Over Temperature Warning on Emerson UPS, and how can I fix it?
If the Emerson UPS displays 'BM Over Temperature Warning', it indicates that the internal battery module temperature is at an elevated level. Check the air filters located behind the bezels and clean them if necessary. Also, verify that the ambient temperature is not too high. If the problem persists, contact your local Liebert Service representative.
How to troubleshoot Power Module Fan Failure on Emerson UPS?
If you see 'Power Module Fan Failure' on your Emerson UPS, it means one or more of the power module fans has failed. Check to see if the fan is blocked. If it is not blocked, contact your local Liebert Service representative.
General| Model | Liebert APS |
|---|---|
| Category | UPS |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Input Voltage | Varies by model |
| Input Frequency | 50/60 Hz |
| Output Voltage | Varies by model |
| Output Frequency | 50/60 Hz |
| Form Factor | Varies by model |
| Topology | Varies by model |
| Efficiency | Varies by model |
| Battery Type | Varies by model |
| Battery Voltage | Varies by model |
| Runtime | Varies by model |
| Communication Interface | Varies by model |
| Operating Temperature | 0° to 40°C (32° to 104°F) |
| Humidity | Varies by model |
Provides an overview of the modular UPS system's purpose, capabilities, and adaptability.
Lists the key features and advantages of the Liebert APS UPS system.
Explains the fundamental operating principles of the Liebert APS UPS.
Details the different operating modes the UPS can function in.
Describes the main components of the Liebert APS UPS system.
Instructions for checking the UPS upon delivery for damage or discrepancies.
Specifies the required environmental conditions for UPS installation.
Lists the necessary tools for setting up the UPS.
Guidelines for selecting an appropriate installation site for the UPS.
Procedures for safely unloading the heavy UPS unit from its pallet.
Guides for the physical installation of the UPS unit.
Instructions for installing various modules into the UPS frame.
Detailed procedures for connecting input and output power cables.
Procedures for initial UPS system startup and commissioning.
Describes the Liebert IntelliSlot ports for communication options.
Explains the function and pin definition of dry contact ports.
Details the REPO connection for remote emergency power off.
Information on connecting temperature probes for battery management.
Describes the USB port for monitoring and connectivity.
Information about Liebert MultiLink software for UPS monitoring and control.
Details the LCD port for communication with the display module.
Provides an overview of the UPS display panel and its components.
Describes the various screens and displays available on the LCD.
Gives detailed descriptions of each display screen and its contents.
Instructions on how to enter the control password for settings access.
Explains how to modify UPS operational parameters through the menu.
Lists possible alarm messages and their corrective actions.
Guides on troubleshooting issues with UPS modules using LED indicators.
Provides procedures for replacing or adding UPS modules.
Recommendations for optimal UPS maintenance and care.
Outlines recommended monthly and annual maintenance tasks.
Procedures for cleaning or replacing UPS fan filters.
Tables providing estimated battery run times based on load and battery configuration.
Battery run time tables for specific AS1/ASA model numbers.
Battery run time tables for specific AS2/ASB model numbers.
Battery run time tables for specific AS3/ASC model numbers.
Battery run time tables for specific AS4/ASD model numbers.
Battery run time tables for specific AS5/ASE model numbers.
To Next Page