To Next PageTo Next Page
Need help?Do you have a question about the Enviro Q1LI and is the answer not in the manual?
General| Venting | Direct Vent |
|---|---|
| Ignition System | Electronic Ignition |
| Fuel Type | Natural Gas or Propane |
| Style | Modern |
| BTU Input (NG) | 24, 000 BTU |
| BTU Input (LP) | 24, 000 BTU |
Crucial safety warning regarding fire and explosion risks from non-compliance.
Step-by-step instructions on immediate actions if gas is detected.
Instructions for installers and consumers regarding manual retention.
Specific safety warnings and code requirements for Massachusetts installations.
General safety guidelines for installation, operation, and maintenance of the appliance.
Specific safety instructions and warnings for operating the appliance safely.
Warning about hot glass surfaces and precautions to prevent burns, especially for children.
Explanation of direct vent technology and appliance suitability for various altitudes.
Details on standards and certifications for the Q1LI model, including gas types.
Bullet points detailing key features and approval notes for the Q1LI fireplace.
Instructions for the initial burn-in period, including smoke and cleaning procedures.
Detailed dimensional drawings and measurements for the Q1LI unit (Top Vent and Rear Vent).
Information on where to find the rating label and lighting instructions on the unit.
Instructions for safely lighting and turning off the fireplace using the remote control.
Critical safety warnings before the initial operation of the appliance.
Step-by-step guide for operating the fireplace via the remote control.
Procedure for safely turning off the gas supply to the appliance for maintenance or shutdown.
Explanation of the air shutter adjustment lever and its effect on flame appearance.
Table detailing normal operational sounds and their causes.
Overview of the Proflame 2 remote control system and its functions.
Details the components of the Proflame 2 Remote Control System (Transmitter and IFC).
Provides technical specifications for the Transmitter and Integrated Fireplace Controller (IFC).
Description of the Proflame 2 Transmitter, its features, and button layout.
Explanation of the Proflame 2 IFC, its connections, power, and synchronization.
Steps for initializing the Proflame 2 system for the first time.
How to view and verify temperature units on the transmitter display.
Procedure for turning on the appliance using the transmitter.
Instructions for switching between intermittent and continuous pilot modes and their benefits.
How to turn off the appliance using the transmitter.
Using the transmitter as a room thermostat to control comfort level.
Utilizing the smart thermostat function for automatic flame adjustment based on room temperature.
How to adjust the flame height (levels) using the remote control.
How to control the convection fan speed and operation using the transmitter.
Functionality to lock the transmitter keys for safety and prevent unauthorized operation.
How the system indicates low battery levels for the transmitter and IFC.
Annual maintenance procedures to ensure clean and proper system operation.
Instructions for cleaning the fireplace glass when cool, including product recommendations.
Steps for cleaning the firebox, logs, burner, and pilot assembly.
Procedure and warnings for replacing the high-temperature ceramic glass door.
Guidelines for cleaning painted, porcelain, or plated surfaces without damage.
Detailed steps and warnings for removing the glass door for cleaning or maintenance.
Instructions for removing the burner for cleaning, conversion, or replacement.
Instructions for converting the appliance between Natural Gas and Propane, to be performed by a qualified agency.
Step-by-step guide for installing a fuel conversion kit, including safety precautions.
Overview of the installation section, target audience, and safety guidelines.
Guidelines for selecting the fireplace location and framing the opening according to dimensions.
Instructions for converting the unit from a top vent to a rear vent configuration.
Guidance on using ceramic board and fiberglass insulation for rear and top vent configurations.
Instructions for installing standoffs for framing and ensuring proper clearances, with notes for masonry fireplaces.
Dimensions and considerations for installing the fireplace in a corner configuration.
Clearances and material requirements for mantles and non-combustible facings around the unit.
Information about direct vent system requirements, length, and termination.
Instructions for installing the Q1LI as an insert using a co-linear vent adapter kit into solid fuel fireplaces.
Detailed clearances and restrictions for vent termination locations based on Canadian and US codes.
Minimum clearances required for vertical and horizontal vent pipes to combustibles.
List of approved vent manufacturers and their product lines compatible with the Q1LI.
Table listing part numbers for various vent lengths, elbows, and termination components.
Installation guidelines for horizontal rear vent terminations without vertical rise.
Charts showing acceptable vertical rise and horizontal run combinations for top and rear venting.
Information about the co-linear venting adapter kit for installation into masonry fireplaces.
Steps for installing the co-linear venting adapter kit, including component removal and installation.
Guidelines for installing and setting air restrictors for vertical venting to control combustion and flame appearance.
Notes and steps for horizontal vent termination, including clearances and wall penetration.
Steps for vertical vent termination, including ceiling and roof penetration, flashing, and support.
Important notes regarding vent pipe offsets, elbow usage, multi-story installations, and enclosures.
Guidelines for installing the gas fireplace insert into a solid fuel fireplace.
Instructions and warnings for connecting the gas line and performing pressure tests.
Electrical connection and grounding requirements for the fireplace, including wiring diagram.
Step-by-step guide for correctly placing the fire grate, logs, and coal nuggets in the firebox.
Annual maintenance recommendation for logs, including checking for deterioration and soot.
Instructions for installing and removing optional porcelain liner panels.
Explanation of diagnostic LED flash codes and their meanings for troubleshooting.
Details on the ignition attempts and timing sequences of the Proflame2 IFC.
Requirements and conditions for submitting a warranty claim and warranty coverage.
List of conditions and damages not covered by the product warranty.
Responsibilities of dealers in providing purchase and warranty claim information.
Responsibilities of distributors in verifying warranty information.
