Fluke 93 - Page 120

5-24 CALIBRATION ADJUSTMENT PROCEDURE
5»8 Calibration Adjustment Procedure
Summary
This table provides an overview of all steps in the Calibration Adjustment
Procedure. It
is
intended
to
be used as a reference for frequent users. For
details
on howto
perform
each
Calibration
Adjustment
step, refer to sections 5.5, 5.6 and 5.7.
Table 5.5 Calibration Adjustment Procedure Summary.
STEP
I
SIGNAL SOURCE
I
SIGNAL AMPL/FREQ SCOPEMETER INPUTS ACTIONS
CONTRAST Calibration Adjustment Procedure
Adjust for clear picture.
SCOPE Calibration Adjustment Procedure
Hardware SCOPE Calibration Adjustments: only to be done when ScopeMeter is repaired!
HI PM5134 300 mV(pp)/1 kH2 (square) A &
6
(50Q
termin.) Adjust
C21
09^:^2209.
H2 PMS134 3V(pp)/1 kHz (square) A & B (500 termln.) Adjust C2107/C2207.
H3 Tek PG S06 20V(pp)/1 kHz (square) A&B Adjust C2114/C2214,
H4
Fluke 5100B 254.5 mV (RMS)/1 kHz (sine] A Adjust R2346/R2347,
Ground testpcrint 209.
Closed case SCOPE Calibration Adjustments
S5
. _ .
Short circuit BNCs.
S6
PM 5134 300 mVjpp)/1 kHz (square) A&B(5Cm termln.)
-
S7 PM
5134
3V(pp)/1
kHz (square)
A
& B(5011 termln.)
-
S3 Tek PG 506 20V(pp)^1 kHz (square)
A&B
-
59 Tek PG 506 S0V(pp)/1 kHz (square) A&B
-
510 Tek PG 506 20mV(pp)/1 kHz (square) A&B
-
S11
Tek PQ 506 50mV(pp)/1 kHz (square) A&B
-
SI 2 Tek PG 506 too mV{pp)/1
kHz (square) A&B
•
SI 3 Tek PG 506 200
mV(pp)/i
kHz (square)
A&8
-
SI 4
Tek PG 506 600 mV(pp)/1 kHz (square) A&B
-
SI 5 Tek PG 506 1V(pp)/l kHz
(square) A&B
-
SI 6 Tek PG 506 10V(pp)/1 kHz(squ^e) A&B
-
SI 7
Tek
PG 506 lOOV(pp)/1
kHz (square) A&B
-
SI 8 Tek PQ 506 200 mV(pp)/1 kHz (square) A&B
-
519 Tek PG 506 20 mV(pp)/1 kHz (square) A&B
520 Fliice 5100B 353.5 mV (RMS)/50 kHz (sine) A&B
S21
Fluke 5100S 353.5 mV (RMS)/50 kHz (sine) A&B
-
S22 Fluke 5100B
353-5
mV
(RMS)/50
kHz
(sine) A&B
.
523 Fluke S100B 353.5 mV (RMS)/S0 kHz (sine) A&B
-
S24
Fluke S100B 353.5 mV (RMS)/S0 kHz (sine) A & banana
-
S25 Tek PG 506 500
mV(pp)/l
MHz
A&B
(500
termln.)
-