Fujitsu ESPRIMO K55x/24 Series

Questions and Answers

A
Angela JohnsonAug 9, 2025
What to do if Fujitsu ESPRIMO K55x/24 power indicator remains off?
- A
  Alicia MaxwellAug 9, 2025
  If the power indicator on your Fujitsu Desktop remains off after switching it on, there might be a problem with the power supply. First, ensure the power cable is correctly plugged into both the device and a grounded mains outlet, and that the main switch at the rear is set to the "I" position. If this doesn't work, the internal power supply might be overloaded. Unplug the device, wait about 3 minutes, then plug it back into a grounded outlet and switch it on again.
B
Bryan HernandezAug 13, 2025
What to do if the external monitor remains blank on Fujitsu ESPRIMO K55x/24 Desktop?
- K
  krista35Aug 13, 2025
  If the external monitor remains blank when connected to your Fujitsu Desktop, try these steps: * Ensure the monitor is switched on. * Press any key to rule out power saving mode. * Adjust the monitor's brightness. * Check the power and data cables are properly connected to both the system and the monitor. Turn off the monitor and the system before checking the cables. * If the screen output is set to the system’s LCD monitor, press the key combination to switch the screen output.
D
Donna GutierrezAug 16, 2025
How to fix Fujitsu ESPRIMO K55x/24 Desktop when it cannot be switched off?
- M
  Michael YorkAug 16, 2025
  If your Fujitsu Desktop cannot be switched off using the On/Off switch, it might be due to a system crash. Press and hold the On/Off switch for at least 4 seconds until the device turns off. Be aware that this could lead to data loss, as the operating system isn't shut down properly.
S
Steven FowlerAug 21, 2025
Why is there no mouse pointer displayed on the Fujitsu ESPRIMO K55x/24 Desktop monitor?
- M
  mendezjenniferAug 21, 2025
  If there is no mouse pointer displayed on the monitor of your Fujitsu Desktop, the mouse might not be properly connected. Shut down the operating system correctly, then switch the device off. Check that the mouse cable is properly connected, including any adapters or extension leads. Ensure that only one mouse is connected before switching the device back on.
M
Mrs. Melissa TurnerAug 26, 2025
What to do if the external monitor is blank or the image is unstable on Fujitsu ESPRIMO K55x/24?
- S
  Sara HansonAug 26, 2025
  If the external monitor is blank or the image is unstable on your Fujitsu Desktop, it could be due to an incorrect monitor selection or screen resolution. Terminate the application program in Windows by pressing Alt + F4. If the error persists, switch to the system's LCD monitor and set the screen resolution as described in your operating system's documentation.
S
Samantha CrawfordAug 29, 2025
Why is the internal screen blank on my Fujitsu Desktop?
- D
  Dawn DixonAug 30, 2025
  If the internal screen of your Fujitsu Desktop stays blank, it could be due to several reasons: * Power saving mode might be activated, so press any key on the keyboard or deactivate the screen saver. * The brightness control might be set too low; adjust it to increase the brightness. If the screen display becomes too dark, check the ambient temperature.
L
Leslie Long DDSSep 3, 2025
What to do if SmartCard reader is not recognised on Fujitsu Desktop?
- T
  Timothy LeSep 3, 2025
  If the SmartCard reader on your Fujitsu Desktop is not recognized, make sure you have inserted your SmartCard correctly into the SmartCard reader with the chip facing upwards. Also, verify that the SmartCard you are using complies with the ISO standard 7816-1, -2, -3 and -4.