Why are the generated images elongated on Fujitsu Scanner?
If the generated images are elongated when using your Fujitsu Scanner, clean the Feed rollers. For Windows 98, Me, 2000, and XP, adjust the scale in "Scanners and Cameras" in the control panel. For Windows 95 and NT 4.0, adjust the scan scale in the Scanner Control Center.
Why is my Fujitsu fi-5220C Scanner image distorted?
If the generated image is shifted or distorted, ensure that the documents are loaded correctly.
How to fix shadow on Fujitsu fi-5220C Scanner image?
A shadow on the leading edge of the scanned image may be due to dirty Feed rollers. Clean the Feed rollers. You can also adjust the [Sub-scan Setting] within [Scanners and Cameras] in the control panel.
How to improve Fujitsu Scanner image quality?
Unsatisfactory image quality can be caused by dirty glass. Clean any dirty locations.
Why are my Fujitsu fi-5220C images elongated?
Elongated images can be caused by dirty Feed rollers. Clean the Feed rollers. Also, for Windows 2000 and Windows XP, adjust the scale in the [Device Set] tab within "Scanners and Cameras" in the control panel.
How to remove vertical lines from Fujitsu Scanner images?
If vertical lines appear in the scanned image, it might be due to dirty glass. Clean the glass as instructed in the Operator's Guide "3. Daily Care".
What to do if Fujitsu fi-5220C Scanner paper is not fed?
If paper is not feeding, first check that the documents meet the "Document Quality" and "Multi feed Detection Conditions" requirements. A dirty Pick roller can also cause this issue, so clean it. If the Pick roller is worn out, replace it. Finally, make sure there is no dirt or dust in the document feed path.
Why does my Fujitsu fi-5220C multi feed?
Multi feed issues can occur if the documents do not meet the "Document Quality" and the "Multi feed Detection Conditions". Ensure your documents meet these standards. Also, fan the documents before scanning, correctly align them, and load them onto the ADF paper chute. If the stack of documents is thicker than 5 mm, reduce the number of sheets. Another cause may be a dirty Pad ASSY, so clean it. If the Pad ASSY is worn out, consider replacing it.
What to do if generated image shifts or is distorted on Fujitsu Scanner?
If the generated image from your Fujitsu Scanner shifts or is distorted, ensure you are loading the documents correctly.
What to do if scanning does not commence on Fujitsu Scanner?
If scanning does not start on your Fujitsu Scanner, try these steps: Realign and reload the documents on the ADF paper chute, and ensure the ADF is completely closed. Check the cable connection (and the hub's power supply if using a USB hub). If there is an alarm or error, turn the power off and on again. If the alarm persists, it may require professional attention.
Covers electrical, environmental, and handling safety rules.
Addresses safe operation regarding damage, odors, and internal components.
Covers safe installation surfaces, plugs, ventilation, and temperature changes.
Details static electricity, sprays, scanner use, power disconnect, and shipping locks.
Procedures for loading documents into the ADF.
Procedures for loading documents onto the flatbed.
Guides on using ScandAll 21 to scan documents.
Procedures for scanning documents on both sides.
Methods for saving scanned images as PDF files.
How to configure multi-feed detection to prevent document feeding errors.
Procedures for clearing document jams from the ADF.
Explains error codes displayed on the operator panel.
Flowcharts to diagnose and resolve common scanner issues.
General| Film scanning | No |
|---|---|
| Color scanning | Yes |
| Input color depth | 24 bit |
| Maximum scan size | 210 x 297 mm |
| Optical scanning resolution | 600 x 600 DPI |
| Flatbed scan speed (b/w, A4) | 2 sec/page |
| Scanner type | Flatbed & ADF scanner |
| Sensor type | CCD |
| ISO A-series sizes (A0...A9) | A4, A5 |
| Maximum ISO A-series paper size | A4 |
| Auto document feeder (ADF) input capacity | 50 sheets |
| USB version | 2.0 |
| Standard interfaces | SCSI, USB 2.0 |
| Bundled software | -FJ TWAIN driver. -Scandall. -Adobe Acrobat. -ISIS Driver. -QuickScan (demo). -Soft IPC (demo). -VRS 4.1 Basic. |
| Dimensions (WxDxH) | 302 x 569 x 229 mm |
| Power requirements | 100-240 VAC |
| Power consumption (standby) | 6 W |
| Power consumption (typical) | 34 W |
| Operating temperature (T-T) | 5 - 35 °C |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Weight | 8400 g |
|---|
To Next Page