FUTABA 32MZ-WC - MODEL MENU (HELICOPTER); Condition Hold function ONOFF button; PIT CurvePitch Trim; Acceleration

178
＜
Model Menu (Helicopter)
＞
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
02'(/0(18+(/,&237(5
This section contains information on the commands that
apply to helicopters only. For instructions on Airplanes
and Gliders, refer to the sections pertaining to those
aircraft. Each of these functions can be set independently
for different flight conditions. To get to these settings,
touch the desired function button to be accessed.
Use the Model Type function in the Linkage Menu to
select the swash type matched to the fuselage beforehand.
If you later change model types, all settings will be lost.
$OVRDGGÀLJKWFRQGLWLRQVDWWKH&RQGLWLRQ6HOHFWVFUHHQ
before setting the model data at each function. (Up to
eight conditions can be used)
The AFR function, fuel mixture and other functions
common to all model types, are described in a separate
section.
0RGHO0HQXIXQFWLRQVKHOLFRSWHUWDEOH
PIT Curve:$GMXVWVUHVSRQVHLQGLIIHUHQWÀLJKWFRQGLWLRQV
THR Curve: Throttle curve and hovering trim adjustment
Acceleration:&RXQWHUDFWVWRUTXHGXHWRVXGGHQWKURWWOHDQGSLWFKFRPPDQGV
Throttle Hold: Moves the throttle to idle during autorotation
Swash Mix:&RPSHQVDWHVIRUHDFKFRQWUROUHVSRQVH
Throttle Mix:&RPSHQVDWHVIRUSRZHUORVVZKHQF\FOLFDSSOLHG
Pit to Needle:$GMXVWVUHVSRQVHFXUYHLQGLIIHUHQWÀLJKWFRQGLWLRQV
Pit to RUD:+DQGOHVWRUTXHFKDQJHVIURPSLWFKDQJOHLQSXWV
Fuel Mixture:&RPPDQGVDVHFRQGVHUYRWRDGMXVWWKHIXHOPL[WXUHDWWKHFDUEXUHWRU
Gyro: Used to switch Futaba GY series gyro sensitivity
Governor: Used to switch RPM of the helicopter’s head
Throttle Limiter: Limits the high range of the throttle movement by any slider or trimmer
Condition Hold function ON/OFF button
1. Set the throttle stick lower than the 1/3 point.
2. Push the INH button to activate the condition hold function.
7KLVIXQFWLRQPD\EHXVHGWROLPLWWKHPD[LPXPVSHHGRIWKHHQJLQHVRWKDW\RXPD\DGMXVWÀLJKWFRQGLWLRQVZKHQWKHHQJLQHLV
running. An alarm indicates that the function is operating. It will prevent the engine from racing dangerously when adjusting the Idle-
Up settings.
:KLOHWKLVIXQFWLRQLVDFWLYHWKHWKURWWOHVHUYRSRVLWLRQLV¿[HGDWWKHSRLQWWKDW\RXKDYHLQGLFDWHGZKHQWKHIXQFWLRQLVDFWLYDWHG<RX
must deactivate this function when you are through making adjustments.
The system will not allow you to activate/deactivate this function in either of the following states:
 :KHQDQ\RIWKHÁLJKWFRQGLWLRQVZLWFKHV
are on.
 :KHQWKHWKURWWOHVWLFNLVKLJKHUWKDQWKH
1/3 point.
+(/,&237(5