FUTABA 32MZ-WC - Curve setting examples; Throttle Hover trim; Setting method

183
＜
Model Menu (Helicopter)
＞
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
+(/,&237(5
Normal Curve Idle-up 1 Curve Idle-up 2 Curve
Ɣ7KURWWOH&XUYH([DPSOH
The curves shown below were created by using the Line
mode and inputting the data of the 5 points 0% (low
side), 25%, 50% (center), 75%, 100% (high) side at each
condition. They were created by reducing the number
points of the line to 5. When actually creating a curve,
HQWHUWKHGDWDVSHFL¿HGSHUWKHIXVHODJHRUWKHUHIHUHQFH
value).
Curve setting examples
ŏ 5HWXUQ WR 0RGHO 0HQX
7KURWWOH+RYHUWULP
7KH7KURWWOH+RYHUWULPVHWXSVFUHHQFDQEHVHOHFWHGIURPWKH7+5&XUYHVHWXSVFUHHQ
ŏ 6HWV 7KURWWOH +RYHU WULP
ŏ 6HWV WKH GLDO XVHG
The Throttle Hover function trims the throttle near
the hovering point. Normally, use it with hovering
FRQGLWLRQV&KDQJHVLQURWRUVSHHGDFFRPSDQ\LQJ
changes in the temperature, humidity, and other flight
conditions can be trimmed. Adjust the throttle so that
rotor rotation is most stable. More delicate trimming is
also possible by using this function along with the Hover
Pitch function.
Setting method
ŏ :KHQ XVLQJ WKH KRYHULQJ QRUPDO FRQGLWLRQ RQO\ VZLWFK
WKH >*U@ JURXS EXWWRQ PRGH WR WKH >6QJO@ VLQJOH
PRGH DQG PDNH WKH VHWWLQJV
ŏ 6HW WKH IXQFWLRQ WR $&7 >21@
ŏ 6HOHFW WKH DGMXVWPHQW NQRE 6HOHFWLRQ H[DPSOH 5'
ŏ 7KH WULP RSHUDWLRQ PRGH 0RGH &7501250 FDQ EH
selected.
CTRM mode: 0D[LPXP FKDQJH QHDU FHQWHU E\ FHQWHU
WULP RSHUDWLRQ 'RHV QRW FKDQJH DW HQG RI WKH VWLFN
PRYHPHQW
NORM mode: 1RUPDO WULP OLQHDU RSHUDWLRQ 7KH
DGYDQWDJH RI XVLQJ WKLV PRGH LV WKDW KRYHULQJ WKURWWOH
FDQ EH DGMXVWHG ZLWKRXW FKDQJLQJ WKH FXUYH
ŏ 7ULP DGMXVWPHQW UDQJH 5DQJH VHWWLQJ
 :KHQ WKH YDOXH LV PDGH VPDOO WULP DFWV RQO\ QHDU WKH
center.
ŏ 7KH WULP UDWH FDQ EH DGMXVWHG DQG WKH RSHUDWLRQ
direction can be set.