FutureLogic Gen2 Universal PSA-66-ST2RU

To Next Page

To Previous Page

Operators and Technicians Manual

MNL-000032 REV.D

Index

bezel, 4

black mark indexed paper, 6

configuration ticket, 7

errors

Head Up, 4, 5

Missing Black Index Mark, 4, 5

Paper Jam, 4, 5

Paper Out, 4, 5

Print Head, 4, 5

Temperature, 4, 5

Voltage, 4, 5

FEED button, 3, 6

LEDs, 4

paper

capacity, 2

feeding, 6

specifications, 20

paper jam, clearing, 7

part numbers, 21

print head, cleaning, 8

printer

bezel LED control port, 12

firmware upload port, 17

removing, 10

self test, 7

specifications, 18

RS232/USB interface cable, 13

schematics, 25

sensors, 4

Drawer Open, 4

Paper Low, 4

Paper Out, 4

Paper Taken, 4

Platen Engaged, 5

Printer Open, 5

TCL Editor, 2

ticket dimensional specifications, 20

warranty information, 2

Main Page

Table of Contents3
Manual Overview5
Introduction5
Intended Audience5
Applicability5
Conventions Used in this Document5
Product Overview6
Introduction6
Warranty Information6
Operator Interface7
Introduction7
Operator Indicators and Controls7
Figure 3-1 Operator Indicators and Controls7
Keypad Status Light8
Bezel Operation8
Printer Sensor Functions8
Table 3-1 Keypad Leds Status Reporting Printer Condition8
Table 3-2 Bezel Display Status8
Table 3-3 Sensors8
Printer Errors9
Loading Paper9
Table 3-4 Errors and Error Descriptions9
Feeding Paper10
Figure 3-2 Load a Paper Stack10
Figure 3-3 Feed Paper into Paper Loading Slot10
Performing a Self Test11
Clearing a Paper Jam11
Figure 3-4 Sample Configuration Ticket11
Figure 3-5 Remove the Paper11
Cleaning the Print Head12
Figure 3-6 Open the Lid12
Figure 3-7 Clear the Paper Jam12
Printer Service13
Introduction13
Figure 4-1 Ground Screw and Copper Grounding Clips Location13
Removing the Printer14
Figure 4-2 Disconnect the Coiled Cable Connector14
Figure 4-3 Slide the Printer until It Locks14
Figure 4-4 Remove the Paper15
Figure 4-5 Push Release Bar15
Ports and Cables16
Introduction16
Front Bezel Port16
Figure 5-1 Front Bezel LED Control Port16
Table 5-1 Front Bezel LED Control Port Pin-Outs16
RS232/USB Interface Cable17
Figure 5-2 RS232/USB Interface Cable17
Figure 5-3 RS232/USB Interface Cable, Auxiliary Communications18
Table 5-2 Base Port Cable Pin-Outs18
Table 5-3 RS232 Power/Comm Port Pin-Outs18
Table 5-4 USB Port (Series A) Pin-Outs18
Table 5-5 Bezel LED Control Port Pin-Outs18
RS232 Evaluation Cable19
Figure 5-4 RS232 Evaluation Cable19
Table 5-6 Evaluation Cable Bezel Port Pin-Outs19
GDS Adaptor Cable20
Figure 5-5 GDS Adaptor Cable20
Table 5-7 Evaluation Cable 14 Pin Base Port Pin-Outs20
Table 5-8 Evaluation Cable DB9 RS232 Port Pin-Outs20
Table 5-9 GDS Adaptor Cable Connectors20
Firmware Upload Port21
Figure 5-6 Firmware Upload Port21
Table 5-10 GDS Adaptor Cable Assembly21
Appendix A Technical Specifications22
Appendix B Paper Specifications24
Figure B-1 Ticket Dimensional Specification24
Appendix C Part Numbers - Printer/Spares25
Appendix D Schematics29
Appendix E Regulatory & Compliance35
Index36

FutureLogic Gen2 Universal PSA-66-ST2RU - Index

Table of Contents

Related product manuals