GE Multilin 745 - Page 172

GE Multilin 745

242 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

S6 Testing745

Transformer Management Relay

Setpoints

http://www.GEindustrial.com/multilin

5–98

GE Multilin

Table of Contents

Default Chapter3
- Table of Contents3
Getting Started9
- Cautions and Warnings9
- Inspection Checklist9
- Manual Organization10
Using the Relay10
- Menu Navigation10
- Panel Keying Example12
Changing Setpoints13
- Introduction13
- Using the HELP Key13
- Numerical Setpoints13
- Enumeration Setpoints13
- Text Setpoints14
Security15
- Installation15
- Changing the Passcode15
Overview17
Introduction17
- Description17
- Protection Features18
- Order Codes19
Specifications20
- Applicability20
- Inputs20
- Protection Elements21
- Outputs22
- Miscellaneous23
Installation25
- Case Description25
- Panel Cutout25
- Case Mounting26
- Unit Withdrawal and Insertion27
Typical Wiring29
- Description29
- Rear Terminal Layout29
- Wiring Diagrams31
- Phase Sequence and Transformer Polarity33
- AC Voltage Input34
- Logic Inputs34
- Control Power35
- Tap Position Input35
- RTD Driver/Sensor35
- Output Relays36
- Solid State Trip Output36
- Analog Outputs36
- RS485 / RS422 Communications37
- RS232 Front Panel Program Port38
- Irig-B39
- Dielectric Strength39
Interfaces41
Hardware Interface41
- Front Panel41
- Display41
- Leds42
- LED Indicators42
- Program Port43
- Keypad43
- Setpoint Entry45
- Diagnostic Messages46
- Flash Messages46
Enervista Software Interface47
- Overview47
- Hardware47
Connecting Enervista 745 Setup to the Relay51
- Connecting to the Relay54
Working with Setpoints and Setpoint Files55
- Engaging a Device55
- Entering Setpoints55
- File Support56
- Using Setpoints Files56
Upgrading Relay Firmware61
- Description61
- Saving Setpoints to a File61
- Loading New Firmware61
Advanced Enervista 745 Setup Features63
- Triggered Events63
- Waveform Capture (Trace Memory)63
- Trending (Data Logger)65
- Event Recorder67
- Modbus User Map68
- Viewing Actual Values69
Using Enervista Viewpoint with the 74571
- Plug and Play Example71
Setpoints75
Overview75
- Setpoint Message Map75
- Setpoint Entry78
- Setpoint Write Access78
Auto-Configuration79
- Introduction79
- Dynamic CT Ratio Mismatch Correction79
- Phase Angle Correction83
- Zero-Sequence Component Removal84
- Transformer Types85
- Phase Shifts97
S1 745 Setup98
- Passcode98
- Preferences98
- Communications99
- Resetting101
- Clock101
- Default Messages101
- Scratchpad102
- Installation103
- Upgrade Options103
S2 System Setup104
- Description104
- Transformer104
- Windings 1 to 3106
- Onload Tap Changer107
- Harmonics107
- Flexcurves108
- Voltage Input108
- Ambient Temperature109
- Analog Input110
- Demand Metering110
S3 Logic Inputs112
- Description112
- Logic Inputs 1 to 16112
- Virtual Inputs 1 to 16113
S4 Elements113
- Introduction to Elements113
- Setpoint Group115
- Differential Element115
- Instantaneous Differential122
- Phase Overcurrent123
- Neutral Overcurrent130
- Ground Overcurrent133
- Restricted Ground135
- Negative Sequence Overcurrent138
- Frequency140
- Overexcitation145
- Harmonics149
- Insulation Aging152
- Analog Input Level156
- Current Demand157
- Transformer Overload158
- Tap Changer Failure159
S5 Outputs160
- Introduction to Flexlogic160
- Flexlogic™ Rules161
- Output Relays162
- Trace Memory164
- Virtual Outputs165
- Timers165
S6 Testing165
- Description165
- Output Relays166
- Analog Outputs166
- Simulation167
- Factory Service171
Actual Values173
- Message Map173
A1 Status173
- Date and Time173
- Logic Inputs173
- Virtual Inputs173
- Output Relays176
- Virtual Outputs176
- Self-Test Errors176
A2 Metering177
- Current177
- Harmonic Content180
- Frequency182
- Tap Changer182
- Voltage182
- Demand182
- Ambient Temperature183
- Loss of Life184
- Analog Input184
- Power184
- Energy184
A3 Event Recorder185
- Event Data Clear185
- Event Records186
A4 Product Information188
- Technical Support188
- Revision Codes189
- Calibration189
Target and Flash Messages189
- Target Messages189
- Self-Test Errors191
- Flash Messages193
Commissioning195
General195
- Testing Philosophy195
- Test Equipment195
Preliminary Work198
- Description198
Logic Inputs and Output Relays199
- Logic Inputs199
- Output Relays200
Metering200
- Description200
- Current Inputs200
- Voltage Input201
- Ambient Temperature Input203
- Analog Outputs205
- Tap Position205
Protection Schemes205
- Precautions205
- Harmonic Restrained Percent Differential205
- Neutral Instantaneous Overcurrent 1216
- Negative Sequence Time Overcurrent222
- Negative Sequence Instantaneous Overcurrent224
- Frequency227
- Overexcitation230
- Insulation Aging231
- Tap Monitor Failure232
Auxiliary Protection and Monitoring Functions232
- Transformer Overload234
Placing the Relay into Service234
- Procedure234
Appendix235
- Revision History235
EU Declaration of Conformity236
GE Multilin Warranty237
- Warranty Statement237

Related product manuals

Preview: GE Multilin 750

GE Multilin 750

Preview: GE Multilin 489

GE Multilin 489

Preview: GE Multilin 469

GE Multilin 469

Preview: GE Multilin 369

GE Multilin 369

GE Multilin 350 Series

Preview: MULTILIN 269 MOTOR MANAGEMENT RELAY Series

MULTILIN 269 MOTOR MANAGEMENT RELAY Series

Preview: 745 TRANSFORMER MANAGEMENT RELAY

745 TRANSFORMER MANAGEMENT RELAY

Preview: GE MFAC 14

Preview: GE MiCOM P40

Preview: GE MiCOM P40 Agile P14D

GE MiCOM P40 Agile P14D

GE MiCOM P40 Agile P94V