GE NetworX NX-6V2 User Manual

NetworX
™
Series
NX-6V2 Control Panel
Installation and Startup
Downloaded from: http://www.guardianalarms.net

GE NetworX NX-6V2 Specifications

Power

operating power	16.5 VAC 40, or 50 VA Transformer
auxiliary power with 25 VA Transformer	12 VDC Regulated 500 mA
auxiliary power with 40 or 50 VA Transformer	12 VDC Regulated 1 AMP
auxiliary power with NX-320E Power Supply	12 VDC Regulated 2 AMPS + Control Panel Power

Loop Specifications

loop resistance standard loop	300 Ohms Maximum
loop resistance 2-wire smokes	30 Ohms Maximum
loop response	Selectable 50mS or 500mS

Operating Environment

operating temperature	32 to 120 degrees F

Keypad Specifications

LED keypad current draw	130 mA max.
LED keypad zones normal without sounder	55 mA
LED keypad dimensions	6.4" Wide, 4.0" High, 1.1" Deep
NX148E LCD keypad current draw	110 mA max.
NX148E LCD keypad without sounder	75 mA
NX148E LCD keypad dimensions	6.4" Wide, 5.3" High, 1.0" Deep

Dimensions and Weight

metal enclosure dimension	11.25" Wide, 11.25" High, 3.50" Deep
shipping weight	9 lbs.

Summary

General Description

Wiring Diagram

Terminal Descriptions

Programming the LED Keypads

Keypad Address and Partition Settings

Changing User Codes

Procedure for modifying existing user access codes on the system keypad.

Programming the Control Panel

Entering and Navigating Program Mode

Steps to access the control panel's programming mode and select modules for configuration.

Programming Data Types

Numerical Data Entry and Display

Feature Selection Data Configuration

Loading Factory Defaults

Enrolling Modules and Keypads

Quick Start Installation Guide

Programming Locations Overview

Phone Number 1 Configuration

Setting up the primary phone number for central station communication.

Account Code for Phone 1

Communicator Format for Phone 1

Selecting the communication format for Phone 1 transmissions to the receiver.

Reporting Events to Phone Number 1

Programming Phone Number 2

Communicator Format for Phone 2

Reporting Events to Phone Number 2

Programming Phone Number 3

Communicator Format for Phone 3

Reporting Events to Phone Number 3

Partition 1 Feature and Report Selections

Entry and Exit Timers Configuration

Default Zone Types Configuration

Zone Type and Partition Selection (Zones 1-8)

Zone Type and Partition Selection (Zones 9-16)

Siren and System Supervision Settings

Keypad Sounder Control Options

System Timers Configuration

Special Features Configuration

Go To Program Code Setup

Auxiliary Output Partition Selection

Auxiliary Output Special Timing

Auxiliary Output Event and Time Configuration

Autotest Control Settings

Closing and Automatic Arming Time

Slow Communicator Format Codes

Partition Account Codes

Partition 2 Feature and Reporting Selections

Zone Type 1 Alarm Event Code and Characteristic Select

Zone Types 2-8 Alarm Event Code and Characteristic Select

Zone Types 9-18 Alarm Event Code and Characteristic Select

Zone Types 19-28 Alarm Event Code and Characteristic Select

Zone Types 29-30 Alarm Event Code and Characteristic Select

Programming Worksheets Summary

Phone 1 Programming Worksheet

Phone 2 Programming Worksheet

Phone 3 Programming Worksheet

Glossary of Terms

Abort Definition

AC Fail / Low Battery Report / Warning

Arm / Disarm Codes

Information on setting and using user codes for arming and disarming the system.

Underwriters Laboratories (UL) Information

UL Listed Devices

Installation Instructions for UL Compliance

Mandatory instructions for installing the NX-6V2 to meet UL requirements.

Minimum System Configurations for UL Installations

ANSI / SIA CP-01 Requirements

Technical Specifications