gefran SIEIDrive ADL300

To Next Page

.... Quick start up guide

Specification and installation

SIEIDrive

Vector inverter for lifts with

synchronous/asynchronous

motors

ADL300

Main Page

Information about this Manual2
Table of Contents3
Safety Precautions5
Symbols Used in the Manual5
Safety Precaution5
General Warnings6
Instruction for Compliance with UL Mark (UL Requirements), U.S. and Canadian Electrical Codes7
Introduction to the Product8
Dedicated Features8
Other Features9
Identification of Components10
Product Identification11
Standard Configurations12
Transport and Storage15
General15
Permissible Environmental Conditions15
Specification16
Environmental Conditions16
Standards16
Precision16
Speed Control16
Speed Control Limits16
Torque Control16
Current Rating16
Input Electrical Data17
Output Electrical Data18
Derating Values in Overload Condition19
Derating Values for Switching Frequency19
Kalt: Ambient Temperature Reduction Factor19
Voltage Level of the Inverter for Safe Operations20
Load Consumption (Energy Rating)20
Cooling21
Weights and Dimensions22
Options25
Optional External Fuses25
Network Side Fuses (F1)25
Input Chokes26
AC Input Chokes26
DC Input Chokes26
AC Output Chokes27
External Braking Resistors (Optional)28
EMC Filter (Optional)29
Mechanical Installation30
Maximum Inclination and Assembly Clearances30
Fastening Positions31
Wiring Procedure33
Power Section35
Cable Cross-Sections35
Connection of Shielding (Recommended)36
EMC Guide Line37
Block Diagram of Power Section38
Internal EMC Filter (Standard)39
Power Line Connection39
Connection of AC and DC Chokes (Optional)39
Motor Connection40
Connection of Braking Resistor (Optional)40
Regulation Section41
Cable Cross-Sections42
Connection of I/O Card42
Feedback Connection44
Integrated Safety Card Connection51
Connection Diagrams52
Regulation Potentials, Digital I/O52
Typical Connection Diagram53
Emergency Connection Diagram (with UPS or EMS Module)55
Connection Diagram for Emergency Maneuver (for Synchronous Motor Only)60
Serial Interface (PC Connector)61
Drive/Rs232 Port Point-To-Point Connection61
CAN Interface62
Optional Keypad Interface (Keypad Connector)63
Saving Data on the Memory Card63
Braking64
Braking Unit (Internal)64
Use of the Keypad66
Description of Keypads66
KB-ADL300 Integrated Keypad66
Membrane Keypad66
Meaning of Leds66
KB-ADL Optional Programming Keypad67
Membrane Keypad67
Meaning of Leds67
Navigating with the Integrated Keypad68
Scanning of First and Second Level Menus68
Display68
Changing Values70
Error Messages When Modifying a Parameter71
Displaying and Closing Messages71
Displaying and Resetting Alarms72
Alarm Log72
Startup Wizard72
Motor Self-Tuning73
Asynchronous/Synchronous Selection73
Correspondence Table Displayed Character/Alphabet73
Navigating with the Optional Keypad74
Scanning of the First and Second Level Menus74
Display of a Parameter74
Scanning of the Parameters75
List of the Last Parameters Modified75
FIND" Function75
Parameter Modification75
How to Save Parameters76
Configuration of the Display77
Language Selection77
Selection of Easy/Expert Mode77
Startup Display77
Back-Lighting of the Display77
Alarms77
Alarm Reset77
Messages78
Saving and Recovery of New Parameter Settings78
Selection of the Keypad Memory78
Saving of Parameters on the Keypad78
Load Parameters from Keypad79
Transfer of Parameters between Drives79
Saving and Recovery of New Parameter Settings on Memory Card79
Asynchronous/Synchronous Selection80
Commissioning Via Keypad81
Asynchronous Motor Startup Wizard (with the Integrated Keypad)83
Asynchronous Motor Startup Wizard (with the Optional Keypad)88
Startup Wizard for Brushless Motors (with the Integrated Keypad)95
Startup Wizard for Brushless Motors (with the Optional Keypad)100
Troubleshooting107
Alarms107
Speed Fbk Loss Alarm According to the Type of Feedback111
Reset Speed Fbk Loss Alarm113
Encoder Error Alarm113
Messages114
Appendix117
ADL300 Advanced Configuration117
Inserting Expansion Cards118
I/O Card119
Input/Output Features122
Encoders and Encoder Expansion Cards125
Encoders125
Phasing126
Encoder Cards127
Brake Monitoring System (A3 Amendment)138
Introduction138
Configuration of the Brake Fault Alarm139
Maintenance of the Brake Fault Alarm Function139
Troubleshooting139

Table of Contents

Other manuals for gefran SIEIDrive ADL300

Related product manuals