gefran VDL200 Series - Motor Connection; Connection of Braking Resistor (Optional)

66 pages

To Next Page

To Previous Page

VDL200 • Quick installation guide - Specifications and connection 27

7.1.8 Motor connection

L1 L2 L3 BR C1 CDUVWEM

3 ph

K3MK2M

7.1.9 Connection of braking resistor (optional)

L1 L2 L3 BR C1 CDUVWEM

Braking resistor

Note! Recommended combination braking resistors: see paragraph 5.4.

Main Page

Information about this Manual2
Table of Contents3
Safety Precautions5
Symbols Used in the Manual5
Safety Precaution5
General Warnings6
Disclaimer6
Introduction to the Product7
Dedicated Features7
Other Features8
Identification of Components9
Product Identification10
Transport and Storage11
General11
Permissible Environmental Conditions11
Specification12
Environmental Conditions12
Standards12
Precision12
Speed Control12
Speed Control Limits12
Torque Control12
Current Rating12
Input Electrical Data13
Output Electrical Data13
Derating Values in Overload Condition13
Derating Values for Switching Frequency14
Kalt: Ambient Temperature Reduction Factor14
Voltage Level of the Inverter for Safe Operations14
Load Consumption (Energy Rating)14
Cooling15
Weights and Dimensions16
Options18
Optional External Fuses18
Network Side Fuses (F1)18
Input Chokes18
AC Input Chokes18
DC Input Chokes18
AC Output Chokes19
External Braking Resistors (Optional)19
EMC Filter (Optional)20
Mechanical Installation21
Maximum Inclination and Assembly Clearances21
Fastening Positions22
Wiring Procedure23
Power Section24
Cable Cross-Sections24
Connection of Shielding (Recommended)25
EMC Guide Line25
Block Diagram of Power Section26
Internal EMC Filter (Standard)26
Power Line Connection26
Connection of AC and DC Chokes (Optional)26
Motor Connection27
Connection of Braking Resistor (Optional)27
Regulation Section28
Cable Cross-Sections28
Connection of I/O28
Feedback Connection29
Connection Diagrams31
Regulation Potentials, Digital I/O31
Typical Connection Diagram31
Emergency Connection Diagram32
Serial Interface (PC Connector)33
Drive/Rs232 Port Point-To-Point Connection33
Optional Keypad Interface (Keypad Connector)34
Braking35
Braking Unit (Internal)35
Use of the Keypad36
Description of KB-ADL Optional Programming Keypad36
Membrane Keypad36
Meaning of Leds36
Navigating with the Optional Keypad37
Scanning of the First and Second Level Menus37
Display of a Parameter37
Scanning of the Parameters38
List of the Last Parameters Modified38
FIND" Function38
Parameter Modification38
How to Save Parameters39
Configuration of the Display40
Language Selection40
Selection of Easy/Expert Mode40
Startup Display40
Back-Lighting of the Display40
Alarms40
Alarm Reset40
Messages41
Saving and Recovery of New Parameter Settings41
Selection of the Keypad Memory41
Saving of Parameters on the Keypad41
Load Parameters from Keypad42
Commissioning Via Keypad43
Asynchronous Motor Startup Wizard (with the Optional Keypad)45
Troubleshooting52
Alarms52
Speed Fbk Loss Alarm According to the Type of Feedback55
Reset Speed Fbk Loss Alarm55
Encoder Error Alarm55
Messages56
Appendix59
I/O Specification59
Input/Output Features59
Encoders and Phasing61
Encoders61
Phasing62
Brake Monitoring System (A3 Amendment)63
Introduction63
Configuration of the Brake Fault Alarm64
Maintenance of the Brake Fault Alarm Function64
Troubleshooting64

gefran VDL200 Series - Motor Connection; Connection of Braking Resistor (Optional)

Table of Contents

Other manuals for gefran VDL200 Series

Related product manuals