English (GB)
16
Continued from page 15
4. Settings
1 ->
4.1 Primary controller
4.1.1 PI controller
4.1.2 Alternative setpoints
4.1.2.1 Alternative setpoints 2-7
4.1.3 External setpoint influence
4.1.3.1 Input value to be influenced by
4.1.3.2 Setting of influence function
4.1.4 Primary sensor
4.1.5 Secondary sensor
4.1.6 Clock program
4.1.7 Proportional pressure
4.1.8 S-system configuration
4.1.9 Setpoint ramp
4.2 Pump cascade control
4.2.1
Min. time between start/stop
Max. number of starts/hour
4.2.3 Standby pumps
4.2.4 Forced pump changeover
4.2.5 Pump test run
4.2.7 Pump stop attempt
4.2.8 Pump start and stop speed
4.2.9 Min. performance
4.2.10 Compensation for pump start-up time
4.3 Secondary functions
4.3.1 Stop function
4.3.1.1 Stop parameters
4.3.2 Pilot pump
4.3.3 Soft pressure build-up
4.3.5 Emergency run
4.3.7 Digital inputs
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Function, DI1 (IO 351-41) - DI9, [10-46]
Function, DI1 (IO 351-42) - DI9, [10-46]
4.3.8 Analog inputs
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
4.3.9 Digital outputs
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77-88]
DO1 (IO 351-42), [77] is signalling - DO7 [77-88]
4.3.10 Analog outputs
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
4.3.11 Counter inputs
Volume counter, DI1 (IO 351-41), [10] - DI2[10, 12]
Volume counter, DI1 (IO 351-42), [10] - DI2[10, 12]
4.3.14 Min., max. and user-defined duty
4.3.14.1 Min. duty
4.3.14.2 Max. duty
4.3.14.3 Set user-defined duty
4.3.18 Pilot pump curve data
4.3.19 Pump curve data
4.3.23 Flow estimation
4.3.20 Control source
4.3.22 Fixed inlet pressure
4.3.23 Flow estimation
4.3.24 Reduced operation
4.3.25 Multisensor settings
4.3.27 Differential sensor
4.3.28 Customisable measured value type
4.4 Monitoring functions
4.4.1 Dry-running protection
4.4.1.1 Pressure/level switch
4.4.1.2 Measurement, inlet pressure
4.4.1.3 Measurement, tank level
4.4.2 Min. pressure
4.4.3 Max. pressure
4.4.4 External fault
4.4.5 Limit 1 exceeded
4.4.6 Limit 2 exceeded
4.4.7 Pumps outside duty range
4.4.8 Pressure relief
4.4.9 Log values
4.4.10 Fault, feedback sensor
4.4.11 Non-return valve
4.5 Functions, CU 352
Change language to the service language (English)
Run wizard again
4.5.1 Display language
4.5.2 Units
4.5.2.1 Pressure
4.5.2.2 Differential pressure
4.5.2.3 Head
4.5.2.4 Level 4.5.2.8 Temperature 4.5.3 Date and time
4.5.2.5 Flow rate 4.5.2.9 Power 4.5.4 Password
4.5.2.6 Volume 4.5.2.10 Energy 4.5.5 Ethernet
4.5.2.7 Specific energy 4.5.6 GENIbus number
4.5.9 Software status
4.6 Status display menu
To Next Page
Loading...
