Grundfos Control MPC 2000 Series User Manual

English (GB)
17
8.2 Overview
Section Display and display number Page
8.4 Status (1) 19
8.4.1 8.4.1 Actual alarms (3.1) 20
8.4.2 8.4.2 System (1.2) 20
8.4.3 8.4.3 Operating mode (1.2.1) 20
8.4.4 8.4.4 Setpoint (1.2.2) 21
8.4.5 8.4.5 Setpoint influence (1.2.3) 21
8.4.6 8.4.6 Measured values (1.2.4) 21
8.4.7 8.4.7 Analog inputs (1.2.5) 21
8.4.8 8.4.8 Log graph (1.2.6) 22
8.4.9 Battery status (1.2.7) 22
8.4.10 8.4.10 Pump 1-6, Pilot pump (1.3 - 1.10) 22
8.5 Operation (2) 23
8.5.1 8.5.1 Operation (2) 23
8.5.2 8.5.2 System operating mode (2.1.1) 23
8.5.3 8.5.3 Control mode (2.1.2) 24
8.5.4 8.5.4 Alternative setpoints (2.1.3) 26
8.5.5 8.5.5 Individual pump control (2.1.4) 26
8.5.6 8.5.6 Pump 1-6 (2.1.4.1 - 2.1.4.6) 27
8.5.7 8.5.7 Operation, pilot pump (2.1.4.7) 27
8.6 Alarm (3) 28
8.6.1 8.6.1 Alarm status (3) 28
8.6.2 8.6.2 Actual alarms (3.1) 29
8.6.3 8.6.3 Alarm log (3.2) 29
8.6.4 8.6.4 Service contact information (3.3) 29
8.7 Settings (4) 30
8.7.1 8.7.1 Primary controller (4.1) 30
8.7.2 8.7.2 PI controller (4.1.1) 31
8.7.3 8.7.3 Alternative setpoints (4.1.2) 32
8.7.4 8.7.4 Alternative setpoints 2-7 (4.1.2.1 - 4.1.2.7) 32
8.7.5 8.7.5 External setpoint influence (4.1.3) 33
8.7.6 8.7.6 Setting of influence function (4.1.3.2) 34
8.7.7 8.7.7 Primary sensor (4.1.4) 34
8.7.8 8.7.8 Secondary sensor (4.1.5) 35
8.7.9 8.7.9 Clock program (4.1.6) 35
8.7.10 8.7.10 Proportional pressure (4.1.7) 36
8.7.11 8.7.11 S-system configuration (4.1.8) 37
8.7.12 8.7.12 Setpoint ramp (4.1.9) 37
8.7.13 8.7.13 Pump cascade control (4.2) 38
8.7.14 8.7.14 Min. time between start/stop (4.2.1) 38
8.7.15 8.7.15 Max. number of starts/hour (4.2.1) 38
8.7.16 8.7.16 Standby pumps (4.2.3) 39
8.7.17 8.7.17 Forced pump changeover (4.2.4) 39
8.7.18 8.7.18 Pump test run (4.2.5) 40
8.7.19 8.7.19 Pump stop attempt (4.2.7) 40
8.7.20 8.7.20 Pump start and stop speed (4.2.8) 41
8.7.21 8.7.21 Min. performance (4.2.9) 41
8.7.22 8.7.22 Compensation for pump start-up time (4.2.10) 42
8.7.23 8.7.23 Secondary functions (4.3) 42
8.7.24 8.7.24 Stop function (4.3.1) 43
8.7.25 8.7.25 Pilot pump (4.3.2)* 45
8.7.26 8.7.26 Soft pressure build-up (4.3.3) 46
8.7.27 8.7.27 Emergency run (4.3.5) 47
8.7.28 8.7.28 Digital inputs (4.3.7) 47
8.7.29 8.7.29 Functions of digital inputs (4.3.7.1) 48
8.7.30 8.7.30 Analog inputs (4.3.8) 48
8.7.31 8.7.31 Analog inputs (4.3.8.1 - 4.3.8.7) 49

Grundfos Control MPC 2000 Series Specifications

General

Brand	Grundfos
Model	Control MPC 2000 Series
Category	Control Systems
Language	English