Grundfos MAGNA3 Series - Page 118

1
R-value is normalized based on the nominal foam thickness for a circular shape.
ASTM Ecoflex
®
Potable HDPE
Submittal Information
Revision E: Feb. 3, 2014
Project Information
Job Name:
Location:
Part No. Ordered:
Engineer:
Date Submitted:
Contractor:
Submitted By:
Manufacturer’s Representative:
Approved By:
Technical Data
Service Pipe:
High-density polyethylene (HDPE); NSF certified SDR-11
Insulation:
Multilayered, closed-cell, crosslinked polyethylene (PEX) foam
insulation with a thermal conductivity of 0.26 BTU in./sq. ft./hour/°F;
Vapor permeability of 0.1g/100 sq. in./day
Jacket:
Corrugated, seamless HDPE; UV-protected
Operating Limits:
-30°F to 73°F at 160 psig (-34°C to 23°C at 11.0 bar)
-30°F to 100°F at 125 psig (-34°C to 38°C at 8.6 bar)
-30°F to 120°F at 101 psig (-34°C to 49°C at 6.9 bar)
-30°F to 140°F at 80 psig (-34°C to 60°C at 5.5 bar)
Product Information and Application Use
Uponor’s ASTM Ecoflex
®
Potable HDPE features high-density polyethylene (HDPE)
service pipe protected by multilayer PEX-foam insulation and covered by a corrugated,
waterproof HDPE jacket. Use Ecoflex Potable HDPE for cold potable-water, cooling and
low-temperature heating applications.

Part Description
Part
Number
Service
Pipe O.D.
Service
Pipe I.D.
Foam
Thickness
Insulation
Value
1
Bend
Radius
Weight
(lb./ft.)
1¼" Potable HDPE with 5.5" Jacket, 300-ft. coil
5115513
1.660"
1.368"
1.54"
R-7.57
14"
1.0 lbs.
1½" Potable HDPE with 5.5" Jacket, 300-ft. coil
5115515
1.900"
1.554"
1.42"
R-6.75
18"
1.0 lbs.
2" Potable HDPE with 5.5" Jacket, 300-ft. coil
5115520
2.375"
1.943"
1.18"
R-5.36
30"
1.4 lbs.
3" Potable HDPE with 6.9" Jacket, 300-ft. coil
5116930
3.500"
2.860"
1.18"
R-5.27
32"
2.4 lbs.
4" Potable HDPE with 7.9" Jacket, 300-ft. coil
5117940
4.500"
3.680"
1.06"
R-4.76
48"
3.6 lbs.
Installation
Install Ecoflex Potable HDPE in cold potable-water, chilled-water, cooling and low-temperature heating applications. Join pipes through fusion
welding, electro-fusion fittings or HDPE compression fittings (not sold by Uponor). For additional information, refer to the Uponor Pre-insulated
Pipe Systems Design and Installation Manual.
Standards
PE 3408, PE 3608 or PE 3454; AWWA C906; ASTM F714; NSF/ANSI Standard 61
Codes
UPC; IPC; NSPC
Listings
NSF/ANSI 61-certified or NSF-pw
Related Applications
Contact Information
Pre-insulated Pipe Systems
Radiant Heating and Cooling Systems
Snow and Ice Melting Systems
Permafrost Prevention Systems
Turf Conditioning Systems
Uponor, Inc.
5925 148
th
Street West
Apple Valley, MN 55124 USA
Phone: 800.321.4739
Fax: 952.891.2008
www.uponorpro.com
Uponor Ltd.
2000 Argentia Road, Plaza 1, Suite 200
Mississauga, ON L5N 1W1 CANADA
Phone: 888.994.7726
Fax: 800.638.9517
www.uponorpro.com