Table of Contents
iii
Cal Low Command (CALLOWCMD) - - - - - - - - - - - - - -4-13
Cal High Command (CALHIGHCMD) - - - - - - - - - - - - - -4-14
C2 Cal Command (C2CALCMD) - - - - - - - - - - - - - - - -4-14
Read Weight Cal Command (READWEIGHTCAL) - - - - - - -4-15
Perform Integrated Technician Tests (WEIGHSYSTEST) - - - -4-15
Structure (ITECHTEST)- - - - - - - - - - - - - - - - - - -4-15
Search for C2 Load Sensors (C2SEARCH) - - - - - - - - - - -4-16
Read C2 Sensor Serial Number (READC2SERIALNUM) - - - -4-17
Read Status of Module (GETSTATUS) - - - - - - - - - - - - -4-18
Write Parameters (WRITEPARAM) - - - - - - - - - - - - - - -4-18
Read Parameters (READPARAM) - - - - - - - - - - - - - - -4-18
Read Live Weight (READLIVEWEIGHT) - - - - - - - - - - - -4-19
Command Table - - - - - - - - - - - - - - - - - - - - - - - -4-19
Output Table - - - - - - - - - - - - - - - - - - - - - - - - - -4-20
Error Code List - - - - - - - - - - - - - - - - - - - - - - - - -4-21
Timed Out Commands - - - - - - - - - - - - - - - - - - - - -4-21
Return Codes - - - - - - - - - - - - - - - - - - - - - - - - -4-21
Calibration Setup Procedures - - - - - - - - - - - - - - - - - - - -4-21
Setting the Unit of Measure - - - - - - - - - - - - - - - - - - -4-21
Setting the Motion Tolerance Value - - - - - - - - - - - - - - -4-22
Setting the Zero Tolerance Value - - - - - - - - - - - - - - - -4-22
Setting the Auto Zero Tolerance Value - - - - - - - - - - - - -4-22
Setting the Number of Readings Averages - - - - - - - - - - -4-22
Setting the Span Weight Value - - - - - - - - - - - - - - - - -4-22
Setting the WAVERSAVER® Value - - - - - - - - - - - - - - -4-22
CHAPTER 5 - CALIBRATION - - - - - - - - - - - - - - - - - - -5-1
A Brief Description of Chapter 5- - - - - - - - - - - - - - - - - - -5-1
Pre-Calibration Procedures - - - - - - - - - - - - - - - - - - - - -5-1
Electrical Check Procedures - - - - - - - - - - - - - - - - - - - -5-2
Load Cell/Point Input/Output Measurements- - - - - - - - - - -5-2
Load Check - - - - - - - - - - - - - - - - - - - - - - - - - - - -5-3
C2 Calibration - - - - - - - - - - - - - - - - - - - - - - - - - - -5-4
About C2 Calibration - - - - - - - - - - - - - - - - - - - - - -5-4
“THE BUTTON” C2 Calibration - - - - - - - - - - - - - - - - -5-4
C2 Calibration Using Ladder Logic - - - - - - - - - - - - - - -5-6
Hard Calibration - - - - - - - - - - - - - - - - - - - - - - - - - -5-6
Hard Calibration Procedures - - - - - - - - - - - - - - - - - -5-6
Hard Calibration Ladder Logic Example - - - - - - - - - - - - -5-7
CHAPTER 6 - OPERATING PROCEDURES - - - - - - - - - - - -6-1
A Brief Description of Chapter 6- - - - - - - - - - - - - - - - - - -6-1
Input Data - - - - - - - - - - - - - - - - - - - - - - - - - - -6-1
To Next Page
Loading...