HIMA HIQuad X - Operating Tips

To Next Page

To Previous Page

System Introduction

HI 803 211 E Rev. 1.01.00 Page 9 of 110

1.3.2 Operating Tips

Additional information is structured as presented in the following example:

The text giving additional information is located here.

Useful tips and tricks appear as follows:

TIP

The tip text is located here.

Main Page

Figure 26: Redundant Connection to H41X Base Rack and Extension Rack1
Table of Contents3
Introduction7
Structure and Use of the Document7
Target Audience7
Effective Direction from the Processor Module to the Output Module7
Writing Conventions8
Safety Notices8
Operating Tips9
Safety Lifecycle Services10
Safety11
Intended Use11
Application in Accordance with the De-Energize to Trip Principle11
Application in Accordance with the Energize to Trip Principle11
Use in Fire Alarm Systems11
Explosion Protection11
ESD Protective Measures12
Residual Risk12
Safety Precautions12
Emergency Information12
Concept for Hiquad X13
Safety and Availability13
Table 1: Differences of Hiquad H51X Compared to H41X13
Concept for Hiquad H51X14
Figure 1: H51X Base Rack Completely Assembled14
The H51X Mono System15
Figure 2: Example of Safe H51X Mono Operation (1Oo2)15
Figure 3: Example of H51X Mono System16
The H51X Redundancy System17
Figure 4: Example of Safe H51X Redundant Operation (1Oo2)17
Figure 5: Example of H51X Redundancy System19
Concept for Hiquad H41X20
Figure 6: H41X Base Rack Completely Assembled20
The H41X Mono System21
Figure 7: Example of Safe H41X Mono Operation (1Oo2)21
Figure 8: Example of H41X Mono System22
The H41X Redundancy System23
Figure 9: Example of Safe H41X Redundant Operation (1Oo2)23
Figure 10: Example of H41X Redundancy System24
Extension Rack25
Ventilation Concept26
Measures for Reducing the Temperature26
Engineering Support26
Installing the Hiquad X System in the Control Cabinet26
Table 2: Power Dissipation of Standard Control Cabinets26
Figure 11: Extension Rack27
Figure 12: Fan Concept Within the Control Cabinet27
Table 3: Fan Components as a Function of Power Loss27
Heat Dissipation28
Installation Type28
Natural Convection28
Note on the Standard28
Table 4: Definitions for Calculating the Power Dissipation28
Table 5: Installation Types for Control Cabinets28
Product Description29
Backplane29
19-Inch Frame29
Figure 13: 19-Inch Frame29
Table 6: Rack Backplanes29
Figure 14: Dimensions of the 19-Inch Frame30
H51X Backplane31
Supply of the H51X Base Rack31
Figure 15: Rear View of H51X Backplane31
Table 7: Connection to the 24 V Power Supply31
Buffered Voltage for LS1+ and LS2+ in F-PWR 02 Buffer Modules32
5 V Power Supply for Extension Racks32
Signaling Relay for F-PWR 02 Buffer Module, XG632
Table 8: Spring Terminals for Buffered Voltage32
Table 9: Spring Terminals for 5 V Power Supply32
Table 10: Spring Terminals in 5 Signaling Relays for Buffer Module32
H41X Backplane33
Supply of the H41X Base Rack33
Figure 16: Rear View of H41X Backplane33
5 V Power Supply for Extension Racks34
Table 11: Connection to the 24 V Power Supply34
Table 12: Spring Terminals for 5 V Power Supply34
24 V Auxiliary Voltages for I/O Modules and I/O Processing Module35
Figure 17: Connection to the 24 V Power Supply of the Cable Plugs (H41X)35
Table 13: Spring Terminals for 24 V Auxiliary Voltages in I/O Modules35
Extension Rack Backplane36
Figure 18: Rear View of Extension Rack Backplane36
Temperature Monitoring37
Table 14: Thresholds of the Temperature States37
Power Supply38
Figure 19: Mono 24 V Power Supply38
Figure 20: Redundant 24 V Power Supply39
Mono H51X Base Rack (24 VDC)41
Figure 21: Mono Connection to H51X Base Rack (24 VDC)41
Redundant H51X Base Rack (24 VDC)42
Figure 22: Redundant Connection to H51X Base Rack (24 VDC)42
Redundant H51X Base Rack and I/O Level (24 VDC)43
Figure 23: Redundant Connection to H51X Base Rack (24 VDC) and Redundant I/O Level43
H51X Base Rack (24 VDC) I/O Level Via F-PWR 02 Buffer Modules (Optional)44
Figure 24: Mono Connection to H51X Base Rack (24 VDC)44
Mono H41X Base Rack (24 VDC)45
Figure 25: Mono Connection to H41X Base Rack45
Redundant H41X Base Rack (24 VDC)46
Distribution for Hiquad47
Figure 27: 24 VDC Distribution for Hiquad X47
Table 15: Assignment of F 7133 Power Distribution Modules to I/O Module Slots47
VDC Distribution for H51X48
Figure 28: Extension Rack Connected to a 5 VDC (H51X)49
VDC Distribution for H41X50
Figure 29: Extension Rack Connected to a 5 VDC (H41X)50
VDC Additional Power Supply (H51X)51
System Bus51
Table 16: Allowed Power Consumption in Relation to the Number of Power Supply Units51
Table 17: Allowed Power Consumption in Relation to the Number of Power Supply Units51
I/O Bus52
I/O Watchdog (WD)52
Modules53
F-CPU 01 Processor Module53
Operating System53
General Cycle Sequence53
Operating System States53
Table 18: Operating System States, States Entered55
Behavior in the Event of Faults56
Table 19: Operating System States, User Interventions56
F-IOP 01 I/O Processing Module57
F-COM 01 Communication Module57
I/O Modules58
Scope of Application of the I/O Modules58
Mounting Position58
Noise Blanking59
Effects of Noise Blanking59
Configuring Noise Blanking59
Table 21: Example for Calculating the Minimum and Maximum Noise Blanking Time59
Noise Blanking Sequence60
Figure 30: Transient Interference60
Figure 31: Interference Triggers a Safe Response61
Effective Direction of Noise Blanking62
Effective Direction from the Input Module to the Processor Module62
Effective Direction from the Processor Module to the Output Module62
Figure 32: Effective Direction Associated with Noise Blanking and Output Noise Blanking62
Communication63
Licensing63
Connecting the PADT to the System63
Licensing64
Redundancy65
Processor Module Redundancy65
Reducing Redundancy65
Increasing Redundancy65
Redundancy of I/O Modules65
Module Redundancy66
Channel Redundancy66
System Bus Redundancy66
Communication Redundancy66
Safeethernet66
Standard Protocols66
Programming67
Using Variables in a Project67
Variable Types68
Initial Value68
Table 22: Supported Variable Types68
System Variables and System Parameters69
Table 23: System Variables at Different Project Levels69
Resource System Parameters70
Table 24: Resource System Parameters72
Use of the Parameters Target Cycle Time and Target Cycle Time Mode73
Table 25: Settings for Target Cycle Time Mode73
Maximum Communication Time Slice74
Calculating the Maximum Duration of Configuration Connections [Ms]75
The Minimum Configuration Version Parameter76
Rack System Variables77
Table 26: System Parameters for Output Variables77
Table 27: System Parameter for Input Variables80
Locking and Unlocking the Resource81
Forcing82
Time Limits83
Restricting the Use of Forcing83
Force Editor83
Automatic Forcing Reset84
Forcing and Scalar Events84
Cycle Sequence84
User Management85
PADT User Management85
Table 28: Access Modes for the PADT User Management85
PES User Management86
Default User86
Table 29: Parameters for User Groups in the PES User Management87
Setting up PES User Accounts88
Diagnostics89
Light Emitting Diodes89
Diagnostic History89
Table 30: Blinking Frequencies of the Leds89
Table 31: Maximum Number of Entries Stored in the Diagnostic History Per Module Type89
Diagnostic Messages90
Table 32: Data Field of Diagnostic Message90
Online Diagnosis91
Table 33: Diagnostic Information Displayed in the Online View for the Hardware Editor92
Product Data, Dimensioning93
Environmental Conditions93
Dimensioning93
Table 34: Environmental Conditions93
Table 35: Dimensioning of a Hiquad X Controller93
Lifecycle94
Installation94
Mechanical Structure94
Connecting the Field Level94
Grounding94
CE-Compliant Structure of the Control Cabinet95
Surges on Digital Inputs95
Grounding Connectors96
Figure 33: Grounding Connectors for Racks96
Figure 34: Grounding Connections in the Control Cabinet97
Grounding and Shielding Concept of HIMA Control Cabinets98
Figure 35: Grounding and Shielding Concept of the HIMA Standard Cabinet98
Grounding Several Control Cabinets99
Ungrounded Operation99
Grounded Operation99
Figure 36: Control Cabinets with Central Ground99
Shielding Within the Input and Output Areas100
Lightning Protection for Data Lines in HIMA Communication Systems100
Cable Colors100
Connecting the Supply Voltage100
Start-Up101
Starting up the Control Cabinet101
Test of All Inputs and Outputs101
Voltage Connection101
Starting up the PES with Processor Modules (F-CPU 01)101
Faults102
Maintenance and Repairs103
Connecting the Power Supply after a Service Interruption103
Connecting the Redundant Power Supply103
Loading Operating Systems103
Hiquad X Documentation104
Table 36: Overview of the Hiquad X Documentation104
Appendix105
Glossary105
Index of Figures106
Index of Tables107
Index108

HIMA HIQuad X - Operating Tips

Table of Contents

Related product manuals