Hog Technologies Stripe Hog SH8000 User Manual

Name: Hog Technologies Stripe Hog SH8000
Brand: Hog Technologies
Rating: 4 (1 reviews)

192 pages

To Next Page

To Previous Page

180

Spray Bar & Nozzle Conguration

1-877-HOG-ROAD WWW. STRIPEHOGSUPPORT.COM

Default Chapter3
- Table of Contents3
- Welcome7
- Hog Technologies Limited Warranty8
- Caution & Warning Labels9
Section 111
Safety Information11
- General Safety11
- Blasting Safety12
- Nozzle Safety14
- Hose Safety14
- High Pressure Fitting Safety15
- Dumping Safety15
Section 217
Stripe Hog Systems17
- Stripe Hog System Introduction17
- Ultra-High Pressure Water System17
- Hog Arm and Hog Heads27
- Hog Head31
- Thru-Shaft, Spray Bars, Protectors and Nozzles35
- High Pressure Hoses, Connections & Fittings43
- Vacuum Recovery System45
- Handheld Pressure Washer55
- Auxiliary Blasting Tool Connection57
- Electrical System59
- Console Switch Panel61
- Joystick Console63
- Programmable Logic Controller65
- Skip Meter, Skip Speed Remote Control & Video System67
- Waterblasting Hydraulic System69
- Hydrostatic Drive Pump & Motor72
- Engine & Drivetrain72
- Truck Drive System and PTO73
- UHP Pump & Blower Drive Belts77
- Inspection Platform, Access Ladders & Air Hose Connection78
Section 381
Waterblasting Operation81
- Start Up/Shutdown Introduction81
- Pre-Start Inspection82
- Operate Mode/Waterblasting System Startup Procedure83
- Waterblasting Operations86
- Skip Speed Remote Control89
- Dumping Debris Procedure90
- Operate Mode/Waterblasting System Shutdown Procedure92
- Emergency Shutdown Procedure94
- Operating in Freezing Conditions95
- Operation Routine Maintenance96
Section 497
Lubrication & General Maintenance97
- Lubrication & General Maintenance Introduction97
- Lubrication & Grease Point Locations98
- Standoff Adjustment Procedure100
- Clean Water Filter Replacement102
- Bleeding Air from Charge Water Pump104
- Wear Brush Assembly Adjustment105
- Dirt Shield Replacement106
- Nozzle Installation107
- Rupture Disc Replacement109
- Swivel Seal Replacement110
- Vacuum Canister & Filter112
Section 5113
Scheduled Maintenance113
- Scheduled Maintenance Introduction113
- Periodic Maintenance Items113
- High Pressure Hose Installation115
- Ultra High Pressure Pump Scheduled Maintenance116
- Checking UHP Pump Oil Level & Changing Crankcase Oil118
- High Pressure Pump UNI-VALVE Service121
- High Pressure Pump Stuffing Box Packing Replacement125
- Ultra High Pressure Pump Assembly128
- Diverter Valve Assembly130
- Manual Bypass Valve131
- Vacuum Blower Scheduled Maintenance132
- Checking & Changing Blower Gear Case Oil133
- Blower & UHP Pump Drive Belt Adjustment Procedure135
- Vacuum Hose Replacement & Rotation Procedure138
- Shroud Installation139
- Hydraulic System Scheduled Maintenance141
- Changing Hydraulic Fluid & Flushing Tank141
- Replacing Hydraulic Filters142
- OMSI Drive144
- Winterization & Storage Procedures145
- Thru-Shaft Motor Bearing Pre-Load150
- SH8000 Maintenance Matrix165
Appendix 1: Troubleshooting167
- Waterblasting System Troubleshooting167
Appendix 1167
Appendix 2173
- Mobile Spare Parts System174
Tools & Spare Parts173
Appendix 3: Daily Report & Pre-Op Checklist175
- Daily Report175
- Pre-Op Checklist176
Appendix 4177
Nozzle & Spray Bar Configuration177
- Nozzle Configuration Chart177
- Spray Bar Configuration Charts178
- Nozzle Calculation Sheet183
Glossary of Terms185
- Waterblasting Terms185
Appendix 5185
Appendix 6: Customer Support & Support Web Site189
- Customer Support189

Questions and Answers:

Need help?

Do you have a question about the Hog Technologies Stripe Hog SH8000 and is the answer not in the manual?

Hog Technologies Stripe Hog SH8000 Specifications

General

Brand	Hog Technologies
Model	Stripe Hog SH8000
Category	Construction Equipment
Language	English

Hog Technologies Stripe Hog SH8000 User Manual

Table of Contents

Questions and Answers:

Hog Technologies Stripe Hog SH8000 Specifications