Holtek HT66F0175 - Page 18

Rev. 1.50 18 August 28, 2017 Rev. 1.50 19 August 28, 2017
HT66F0175/HT66F0185
A/D Flash MCU with EEPROM
HT66F0175/HT66F0185
A/D Flash MCU with EEPROM
Symbol Parameter
Test Conditions
Min. Typ. Max. Unit
V
DD
Conditions
I
STB
Standby Current (IDLE0 Mode)
3V
No load, all peripherals off,
f
SUB
on
— 3 5 μA
5V — 5 10 μA
Standby Current (IDLE1 Mode)
3V
f
SYS
=f
HXT
=8MHz on, f
SUB
on
No load, all peripherals off
— 0.5 1.0 mA
5V — 1.0 2.0 mA
3V
f
SYS
=f
HXT
=12MHz on, f
SUB
on
No load, all peripherals off
— 0.6 1.2 mA
5V — 1.2 2.4 mA
5V
f
SYS
=f
HXT
=16MHz on, f
SUB
on
No load, all peripherals off
— 2.0 4.0 mA
5V
f
SYS
=f
HXT
=20MHz on, f
SUB
on
No load, all peripherals off
— 2.5 5.0 mA
3V
f
SYS
=f
HIRC
=8MHz on, f
SUB
on
No load, all peripherals off
— 0.8 1.6 mA
5V — 1.0 2.0 mA
3V
f
SYS
=f
HIRC
=12MHz on, f
SUB
on
No load, all peripherals off
— 1.2 2.4 mA
5V — 1.5 3.0 mA
5V
f
SYS
=f
HIRC
=16MHz on, f
SUB
on
No load, all peripherals off
— 2.0 4.0 mA
Standby Current (SLEEP0 Mode)
3V
f
SUB
off, WDT disable
No load, all peripherals off
— — 1.0 μA
5V — — 2.0 μA
Standby Current (SLEEP1 Mode)
3V
f
SUB
on, WDT enable
No load, all peripherals off
— — 3.0 μA
5V — — 5.0 μA
V
IL
Input Low Voltage for I/O Ports
or Input Pins
5V — 0 — 1.5 V
— — 0 — 0.2V
DD
V
V
IH
Input High Voltage for I/O Ports
or Input Pins
5V — 3.5 — 5.0 V
— — 0.8V
DD
— V
DD
V
I
OL
Sink Current for I/O Port
3V V
OL
= 0.1V
DD
16 32 — mA
5V V
OL
= 0.1V
DD
32 64 — mA
I
OH
Source Current for I/O Port
3V
V
OH
= 0.9V
DD
,
SLEDCn [m+1, m] = 00
n = 0 or 1; m = 0, 2, 4 or 6
-1.0 -2.0 — mA
5V -2.0 -4.0 — mA
3V
V
OH
= 0.9V
DD
,
SLEDCn [m+1, m] = 01
n = 0 or 1; m = 0, 2, 4 or 6
-1.75 -3.5 — mA
5V -3.5 -7.0 — mA
3V
V
OH
= 0.9V
DD
,
SLEDCn [m+1, m] = 10
n = 0 or 1; m = 0, 2, 4 or 6
-2.5 -5.0 — mA
5V -5.0 -10.0 — mA
3V
V
OH
= 0.9V
DD
,
SLEDCn [m+1, m] = 11
n = 0 or 1; m = 0, 2, 4 or 6
-5.5 -11.0 — mA
5V -11.0 -22.0 — mA
R
PH
Pull-high Resistance for I/O Ports
3V — 20 60 100 kΩ
5V — 10 30 50 kΩ