Honeywell 900U02-0100 - Figure 114 - Three-Wire RTD Input Connections; Figure 115 - Two-Wire RTD or Ohm Input Connections; Figure 116 - Slidewire Feedback Connections for Actuators

232 ControlEdge HC900 Process & Safety Controller User and Installation Manual Revision 10
May 2019
8 Point Analog Input
Step
Action
Figure 114 – Three-wire RTD input connections
Figure 115 – Two-wire RTD or ohm input connections
Figure 116 – Slidewire feedback connections for actuators
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
Input 1 Input 2
Input 3
Input 4
Input 6
Input 7
Input 8
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
Input 5
2 wire
RTD/OHMS
2 wire
RTD/OHMS
Note:
You must set switches 1- 8
for Ohms.
Note:
Install jumper
wires:
3-23
6-26
8-28
12-32
13-33
16-36
17-37
20-40
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
Input 1 Input 2
Input 3
Input 4
Input 6
Input 7
Input 8
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
2 wire
RTD/OHMS
Input 5
2 wire
RTD/OHMS
2 wire
RTD/OHMS
Note:
You must set switches 1- 8
for Ohms.
Note:
Install jumper
wires:
3-23
6-26
8-28
12-32
13-33
16-36
17-37
20-40
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
Input 1 Input 2 Input 3 Input 4
Input 6
Input 7
Input 8
Slidewire
Slidewire
Slidewire
Slidewire
Slidewire
Slidewire
Input 5
Slidewire
Slidewire
R
F
R
F F F
F
F
F
F
R
R
R R
R
R
Note:
You must set switches 1- 8
for Ohms.
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
1 2 3 7 8 94 5 6 10 11 12 13 17 18 1914 15 16 20
21 22 23 27 28 2924 25 26 30 31 32 33 37 38 3934 35 36 40
Input 1 Input 2 Input 3 Input 4
Input 6
Input 7
Input 8
Slidewire
Slidewire
Slidewire
Slidewire
Slidewire
Slidewire
Input 5
Slidewire
Slidewire
R
F
R
F F F
F
F
F
F
R
R
R R
R
R
Note:
You must set switches 1- 8
for Ohms.