Honeywell Gent Viglion EN54 - Appendix A - Menu Maps for EN54 Vigilon 4-Loop Panel, Vigilon Compact (and VA) Panels

Appendix A - Menu maps for EN54 Vigilon 4-Loop
panel, Vigilon Compact (and VA) panels
The menu options [Control], [SetUp], [Info] and [Test/Eng] are accessible on pressing the MENU ON/OFF button.
Generic Commissioning instructions
80 4188-856_i2_12/06_Generic Vigilon (Compact + VA) Comms.
Appendix A - Menu maps for EN54 Vigilon 4-Loop panel,
[Control]
[Set Up]
[Info]
[Test/Eng]
[Enable]
[Disable]
<etc>
[Sector]
[MSector]
[Device]
[IO Line]
<etc>
[Sector]
[Zone]
[Group]
[AuxRly]
[MSector]
[Comms]
Params
1-8
{}
[E]
[C] [Q]
Params
1-4
{}
[Device]
Params
1-32
{}
[E]
[C] [Q]
Params
1-128
{}
[E]
[C] [Q]
<etc>
Params
1-2
{}
Params
1-255
{}
[E]
[C] [Q]
<etc>
Params
0-15
{}
[E]
[C]
[Port]
<etc>
[Aux Rly]
<etc>
[Sounder]
[Digital]
[Timeslot]
[Sound]
<etc>
[Silence]
[Reset]
<etc>
[StartMA]
[StopMA]
[UserCode
]
Params
1-207
{}
[Loop]
Params
1-207
[Loop]
Params
1-32
{}
[Loop]
Params
1-8
{}
[Action]
[Signal1]
[Off]
[Signal2]
[Signal3]
[E]
[C] [Q]
[Sig1]
[Sig2]
[Sig3]
Params
1-255
{}
[Action]
Params
1-2
{}
[On]
[Off]
[E]
[C] [Q]
Params
1-207
{}
[Loop]
Params
1-8
{}
[Action]
Params
1-4
{}
[On]
[Off]
[Pulse]
Params
1-207
{}
[Loop]
[E]
[C] [Q]
Params
1-8
{}
Params
0-15
{}
[Device]
[E]
[C] [Q]
Params
1-8
{}
Params
1-207
{}
[Loop]
Params
1-16
{}
[Delay]
[On]
Params
HH:MM:SS
{}
[On]
[E]
[C] [Q]
[Pause]
[Build]
<etc>
[E]
[C] [Q]
Params
0-30sec
{}
Params
1-255
{}
[On]
[Off]
[E]
[C] [Q]
Params
1-255
{}
[E]
[C] [Q]
[Sig1]
[Off]
[Sig2]
[Sig3]
[Off]
[Off]
[Node]
[E]
[C] [Q]
[E]
[C] [Q]
EN Vigilon panels with
M V4.37
[ ] Menu mapControl
CC/MCB software
[E]
[C] [Q]
Key
[E] = [Enter]
[C] = [Cancel]
[Q] = [Quit]
[En] = [Enable]
[Dis] = [Disable]
[Verify]
<etc>
Params
0-3
{}
[E]
[C] [Q]
if off
if on
[On]
[Q]
[E]
[C] [Q]
[Test]
[Q]
[Paper Fd]
[Off]
8Line
feeds
[E]
[C] [Q]
******
PRINTER
TEST
******
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGH
IJKLMNOPQRSRUVWXYZ[=]^-`abcdefghijklmnop
qrstuvwxyz{|}
[Printer]
NOTE: The Network commands such as
Master Sector, Master Group are only applicable
when a network card is fitted in the control panel
and Network node.
[Build]
Params
1-255
{}
[E]
[C] [Q]
Params
1-8
{}
[E]
[C] [Q]
[MAlarm]
[E]
[C] [Q]
Commands accessible under engineer (level 3) password only Commands are accessible under customer (level 2) password
[DelayBlk]
Params
1-16
{}
[Delayed]
[E]
[C] [Q]
Params
MM:SS
0-10min
{}
[End]
[E]
[C] [Q]
[Stop]
No password required
[Audio]
See Control
menu map 2-1
[Audio]
See Control
menu map 2-2
[E]
[From]
[C][Q]
[Sig1]
[Sig2]
[Sig1]
[E]
[From]
[C][Q]
#
# - Menu options will show if the printer is fitted
[Off]
[Off]