Honeywell NOTIFIER AM-8000 - Special Parameters - Drift Warning and Line Reliability; Configure NONA Logging, Line Reliability, and Other Options

Pag. 36 Programming Manual SERIEAM
NOTIFIER ITALIA Doc. M-160.2-AM-8000-ENG Rev A1 AM8000_manu-prog-ENG
Enter the parameter to signal the maintenance breakdown,
(expressed in minutes) Default value = 216
DRIFT WARNING FUNCTION - By enabling this function, the control unit generates a signalling when the
sensor exceeds 70% of the alarm threshold for more than 5 minutes.
This signalling can be used as a warning to perform a cleaning of the sensor optical chamber. This function is a
general enable parameter valid for all the control unit points. The DRIFT WARNING function does not replace
the maintenance request signalling, which in any case is always enabled. It is signalled when a sensor detects,
for more than 36 consecutive hours, a value higher than 80 % of the alarm threshold.
2
2
.
.
E
E
n
n
a
a
b
b
l
l
i
i
n
n
g
g
d
d
i
i
s
s
p
p
l
l
a
a
y
y
&
&
l
l
o
o
g
g
i
i
n
n
H
H
i
i
s
s
t
t
o
o
r
r
y
y
F
F
i
i
l
l
e
e
t
t
h
h
e
e
e
e
v
v
e
e
n
n
t
t
s
s
o
o
f
f
m
m
o
o
d
d
u
u
l
l
e
e
s
s
p
p
r
r
o
o
g
g
r
r
a
a
m
m
m
m
e
e
d
d
w
w
i
i
t
t
h
h
T
T
y
y
p
p
e
e
-
-
I
I
D
D
:
:
N
N
O
O
N
N
A
A
3
3
.
.
C
C
h
h
a
a
n
n
g
g
e
e
o
o
f
f
t
t
h
h
e
e
l
l
i
i
n
n
e
e
r
r
e
e
l
l
i
i
a
a
b
b
i
i
l
l
l
l
i
i
t
t
y
y
p
p
a
a
r
r
a
a
m
m
e
e
t
t
e
e
r
r
s
s
To change one or several parameters in this folder select the parameter through the arrow keys (the
characters of the selected field are in Reverse), press the enter key
and use the arrow keys  to change
the parameter; at the end press the enter key
to confirm the datum.
By increasing
the values of each parameter, the control unit becomes less sensitive for the Fault signaling for
the Points installed on the lines.
By decreasing
the values of each parameter, the control unit becomes more sensitive for the faults signaling for
the Points installed on the lines, moreover the Fault warning message is activated: “Line changed par.”
4
4
.
.
O
O
t
t
h
h
e
e
r
r
Enter the parameter to signal the fault for invalid answer
(expressed in number of interrogation polling on the line)
Default value = 05
Enter the parameter to signal Type ID erroneous fault
(expressed in number of interrogation polling on the line).
Default value = 08
Enter the parameter to signal the off circuits fault,
(expressed in number of interrogation polling on the line).
Default value= 10
Enter the parameter to signal a fault for low chamber value
(expressed in number of interrogation polling on the line).
Default value= 20
By selecting “NO” the print and storage
in historical file of events in alarm from
the input modules programmed with
Type-ID “NONA” is disabled
To change the “File “ function press the enter key
use the arrow keys  to change the parameter; at
the end press the enter key
to confirm .
This option will re-activate the Silenced
Outputs in case of a subsequent Alarm.