Honeywell SILENT KNIGHT SK-5208 - Default Settings for 3;1 Format

Model SK-5208 Fire Control/Communicator Installation and Operation Manual
6-4 P/N 151204
6.2.1 Default Settings for 3/1 Format
Table 6-3 displays the default settings which are set in the Misc. Reporting section of
Programming.
Table 6-3: Default Settings for 3/1 Format
Water Alarm Restore 1-30 WH1-WH30 AR1 - AR0 Alarm Restore Code 3 154 001 - 3 154 030
Water Trouble Restore 1-30 WJ1-WJ30 R1 - R0 Restore Code 3 370 001 - 3 370 030
Water Trouble 1-30 WT1-WT30 T1 - T0 Trouble Code 1 370 001 - 1 370 030
Water Unbypass 1-30 WU1-WU30 R1 - R0 Restore Code 3 570 001 - 3 570 030
Communications Failure Line #1 YC1 T1 Trouble Code 1 354 001
Communications Restore Line #1 YK1 R1 Restore Code 3 354 001
Communications Failure Line #2 YC2 T2 Trouble Code 1 354 002
Communications Restore Line #2 YK2 R2 Restore Code 3 354 002
System Battery Restore YR0 R0 Restore Code 3 302 000
System Battery Trouble YT0 T0 Trouble Code 1 302 000
Cold Alarm 1-30 ZA1-ZA30 A1 - A0 Alarm Code 1 153 001 - 1 153 030
Cold Bypass 1-30 ZB1-ZB30 T1 - T0 Trouble Code 1 570 001 - 1 570 030
Cold Alarm Restore 1-30 ZH1-ZH30 AR1 - AR0 Alarm Restore Code 3 153 001 - 3 153 030
Cold Trouble Restore 1-30 ZJ1-ZJ30 R1 - R0 Restore Code 2 370 001 - 3 370 030
Cold Trouble 1-30 ZT1-ZT30 T1 - T0 Trouble Code 1 370 001 - 1 370 030
Cold Unbypass 1-30 ZU1-ZU30 R1 - R0 Restore Code 3 570 001 - 3 570 030
Programming
Option
Menu Item Choices Default Comments
Misc Reporting
Test Time 00:00 - 23:59 12:00
Selects the time of day the control will send an
automatic test signal to a central station receiver.
AC Delay 0-30 Hours 2
Selects the delay time (in hours) before the control
will report an AC power loss to the central station.
Report Walk Test
No 
No zone information will be reported just test
begin and test end.
By Zone
Test begin, test end, and all events in between will
be reported to central station.
*3/1 Alarm
0 - 9
* Event code for 3/1
and 4/2 reporting
formats.
0
Alarms for Fire, Waterflow, Undefined, Heat,
Cold, and Water events.
*3/1 Alarm Rst 2
Alarms restores for Fire, Waterflow, Undefined,
Heat, Cold, and Water events.
*3/1 Supervisory 6 Sprinkler supervisories.
*3/1 Restore 7
Restore reports for Troubles, Supervisories, and
unbypasses. The only exceptions are the restores
listed as alarm restores.
*3/1 Trouble 8
All system and zone troubles, and zone/NAC
bypasses, and NACs troubles.
*3/1 Test 9 All test events.
Table 6-2: Event and Reporting Code by Format
Event SIA8 & 20 SK4/2 3/1 1400 &2300 Contact ID
firealarmresources.com