HP 650 - Page 127

resetting ... 2-9 – 2-10
restart
See reset
Rget commands in NCL ... 1-34 – 1-35
Rgetatr command in NCL ... 1-35
Rgetb command in NCL ... 1-34
Rgetd command in NCL ... 1-35
Rgetda command in NCL ... 1-35
Rgetdn command in NCL ... 1-35
Rgetir command ... 1-34
Rgetr command in NCL ... 1-34
Rgetxr command in NCL ... 1-34
routing engine
failure ... 3-3, 3-6, 3-12 – 3-13
replacing ... 3-27 – 3-30
utilization LEDs ... 2-8, 3-12
routing services ... 1-32, 1-34
Internet Protocol (IP) ... 1-32, 1-34, 1-36,
2-2, 3-20
Novell IPX ... 1-32, 1-34, 2-2
routing table ... 1-34, 3-9, 3-16, 3-20
RS-232 cable ... A-2, A-4
RS-232 console port ... 1-13 – 1-14, 2-2, A-2,
A-8
RS-232 WAN interface ... 2-2, C-4
RS-422 WAN interface ... 2-2, C-4
RS-449 WAN interface ... 2-2, C-4
Rx LED ... 2-7, 3-9
S
safety ... 1-2
safety approvals ... C-3
screen
Copyright ... 1-19
Main menu ... 1-19, 1-21
Statistics Screen menu ... 1-31
screws, mounting ... 1-2, 1-6, 1-8
security ... 1-19, 1-23, 1-27 – 1-28, 1-34,
2-9 – 2-12
self-test ... 1-17 – 1-19, 2-4 – 2-7, 2-10, 2-13,
2-15, 3-8, 3-11 – 3-12
Self-test LED ... 1-17 – 1-18, 2-7, 2-10, 2-13,
2-16, 3-3 – 3-4, 3-6 - 3-8
serial port
See console
serial ports and links
See WAN
severity of events ... 1-30
Simple Network Management Protocol
See SNMP
SNMP: Simple Network Management
Protocol ... 1-34
spanning tree ... 1-30, 2-12
specifications ... C-1 – C-4
speed sensing console ... 1-18 – 1-19, 1-24,
2-2, 2-10, 2-16, 3-14 - 3-15
standards
See specifications
station address ... 3-16 – 3-17
statistics ... 1-27, 1-31 – 1-33, 3-16
circuits ... 1-33
Statistics Screen menu ... 1-31
Stats command in NCL ... 1-31
Status LED ... 1-17 – 1-18, 2-4 – 2-5,
3-3 – 3-4, 3-6 – 3-8
status LEDs
See LEDs
Swap
button ... 2-8
LED ... 2-8
See also hot swap
system name ... 1-22 – 1-23, 1-26, 1-28, 3-20
T
table mounting ... 1-8
TCP/IP protocol suite
See IP
Telnet ... 2-11, 3-16, 3-20
Temp LED ... 1-18, 2-5, 3-8
temperature specifications ... C-2
temperature warning ... 3-8
terminal
25-pin adapter ... A-2, A-4
parameters ... 1-13 - 1-14
terminal used for console ... 1-4,
1-13 – 1-14, 2-2, 3-14 – 3-15, A-2
configuration ... 1-13 – 1-14, 3-15
Test command in NCL ... 1-27
testing
hardware ... 2-10, 2-13
Index-5