SAVE AMP COR, 7-75
save current display, 7-35
save current state
memory card, 7-82
state register, 7-82
saved analyzer state, 7-49
SAVE EDIT, 7-75
SAVE LIMIT, 7-76
save lock on
MEM LOCKED, 7-55
saving a display image on the memory card,
5-14
saving a limit-line table into analyzer memory,
5-8
saving amplitude correction factors into
analyzer memory, 5-8
saving amplitude correction factors on the
memory card, 5-15
saving and recalling data from analyzer
memory, 5-6-9
saving and recalling data from the memory
card, 5-10-18
saving and recalling programs with a memory
card, 5-16
saving a program on the memory card, 5-16
saving a state into analyzer memory, 5-6
saving a state on the memory card, 5-12
saving a trace into analyzer memory, 5-7
saving a trace on the memory card, 5-13
saving
DLPs
from analyzer memory to card,
7-8
saving key definitions from analyzer memory
to card, 7-8
saving limit-line tables on the memory card,
5-15
saving to a memory card, 7-87
saving to spectrum analyzer memory, 7-88
SAV LOCK ON OFF, 5-8, 7-74
scalar
5OtJ
transmission/reflection test set,
10-13
scalar measurements,
10-4
SCALE LOG LIN, 7-76
screen annotation, 2-10-12
on or off, 7-10
screen characters, 7-47, 7-57, 7-82, 7-92
screen data output, 7-28
screen graticule, 7-47
screen title, 7-22
characters, 7-5
clearing, 7-23
RPG TITLE, 7-74
screen title, using an external keyboard,
5-42
SECAM-L, 7-76
segment deletion, 7-33
SELECT 1 2 3 4, 7-76
SELECT AMPLITUD, 5-25, 5-39, 7-76
SELECT DLT AMPL, 5-25, 7-76
SELECT FREQ, 5-25, 5-39, 7-77
SELECT LWR AMPL, 5-25, 7-77
SELECT MID AMPL, 5-25, 7-77
SELECT POINT, 5-38, 7-77
SELECT PREFIX, 7-77
SELECT SEGMENT, 5-23, 7-77
SELECT TIME, 7-78
SELECT TYPE, 7-78
SELECT UPR AMPL, 5-25, 7-78
self-calibration routine
CAL TRK GEN, 1-9
CAL YTF, l-10
self-calibration routines, l-8, 2-16-18
amplitude, 7-13
CAL, 7-13
correction factors, 7-13
frequency, 7-14
frequency and amplitude, 7-14
tracking generator,
7-
14
sensitivity
spectrum analyzer,
3-
15
serial polling, A-l
Service Cal, 7-2, 7-78
Service Diag, 7-2, 7-78
service documentation
Option 915, lo-12
service functions, 7-2
Service Cal, 7-2
Service Diag, 7-2
service options, 9-4
service request, A- 1
clearing, A-l
service tag, 9-6
SET ATTN ERROR, 7-2, 7-78
Set
B&&W\Printer,
7-78
Set Color printer, 7-78
SET DATE, 7-79
SET TIME, 7-79
setting gate delay, 4-33
setting gate length, 4-33
setting the amplitude, 2-13
setting the center frequency, 2-13
setting the marker, 2-14
setting the span, 2-13
setup
power measurement functions, 7-79
printer, 7-69
SGL SWP, 7-79
SHOW OPTIONS, 7-79
signal comparison,
3-
12
SIGNAL ID, 7-79
signal peak
Index-l 5
To Next Page
Loading...
