HP ProLiant ML30 Gen10 Plus

To Next Page

To Previous Page

12. Connect the SATA-power Y-cable to the drive, and then route the cable through the clip on the optical drive cage.

13. Slide the optical drive into the media bay until it clicks into place.

Installing an optical drive 112

Main Page

Table of Contents3
Component Identification7
Front Panel Components8
Front Panel LED and Button10
Front Panel LED Power Fault Codes11
Rear Panel Components12
Rear Panel Leds13
System Board Components14
System Maintenance Switch Descriptions16
DIMM Slot Location17
DIMM Label Identification18
Drive Bay Numbering19
HPE Basic Drive LED Definitions22
Pcie4 Slot Description23
Pcie Expansion Slot Definitions24
HPE Ns204I-P Nvme os Boot Device Components25
HPE Ns204I-P Nvme os Boot Device LED Definitions26
Fan Numbering27
Fan Mode Behavior28
Media Device Screws29
Trusted Platform Module 2.030
Trusted Platform Module 2.0 Guidelines31
Bitlocker Recovery Key/Password Retention Guidelines32
Operations33
Power up the Server34
Power down the Server35
Remove the Server from the Rack36
Remove the Front Bezel38
Remove the Access Panel39
Remove the Air Baffle41
Remove the PCI Blank Retainer43
Remove a Media Drive44
Install the PCI Blank Retainer46
Install the Air Baffle47
Install the Access Panel48
Install the Front Bezel49
Install the Server into the Rack50
Setup54
Initial System Installation55
HPE Installation Service56
Setting up the Server57
Setting up the Server in Tower Mode59
Operational Requirements60
Space and Airflow Requirements61
Temperature Requirements62
Power Requirements63
Electrical Grounding Requirements64
Rack Warnings and Cautions65
Server Warnings and Cautions67
Electrostatic Discharge68
Hardware Options Installation69
Hardware Option Installation Guidelines70
Tower-To-Rack Conversion Kit71
Installing the Tower-To-Rack Conversion Kit72
Install the Rack Rails and Server Tray73
Install the Server into the Rack77
Drive Options81
Drive Installation Guidelines82
Installing a Non-Hot-Plug LFF SATA Drive83
Installing a Hot-Plug LFF/SFF SAS or SATA Drive87
Power Supply Options90
Hot-Plug Power Supply Calculations91
Power Supply Warnings and Cautions92
Installing a Flexible Slot Power Supply93
Redundant Power Supply Enablement Option95
Installing the RPS Enablement Option96
Media Device Options99
SAS LTO Tape Drive Option100
Installing a SAS LTO Tape Drive101
USB RDX Backup System Option105
Installing a USB RDX Docking Station106
Optical Drive Option109
Installing an Optical Drive110
PCI Fan and Air Baffle Options114
Installing the PCI Fan and Air Baffle115
Storage Controller Options118
Preparing the Server for Storage Controller Installation119
Installing a Type-P Pcie Plug-In Controller Option120
Storage Controller Guides123
Energy Pack Options124
HPE Smart Storage Battery124
HPE Smart Storage Hybrid Capacitor126
Minimum Firmware Versions127
Installing an Energy Pack128
Expansion Card Options131
Installing an Expansion Card132
Memory Option135
DIMM Population Information136
DIMM Installation Guidelines137
Installing a DIMM138
Ilo-M.2-Serial Module Option141
Ilo-M.2-Serial Module Components142
Installing the Ilo-M.2-Serial Module143
M.2 SSD Options151
Installing an M.2 SSD on the System Board152
Installing the Ns204I-P Gen10 Plus Boot Device Option156
Installing the M.2 SATA SSD Enablement Option160
Installing an M.2 SSD on the Ilo-M.2-Serial Module164
Internal USB Device Option167
Installing an Internal USB Device168
Cabling170
Cabling Guidelines171
Storage Cabling173
Drive Power Cabling174
Storage Controller Cabling176
LFF Non-Hot-Plug Drive Controller Cabling177
LFF / 8 SFF Hot-Plug Drive Controller Cabling178
Energy Pack Cabling180
Storage Controller Backup Power Cabling181
Media Device Cabling182
LTO Tape Drive Cabling183
RDX Backup System Cabling185
Optical Drive Cabling187
M.2 SATA SSD Add-In Card Cabling189
Fan Cabling190
PCI Fan Cabling191
System Fan Cabling192
Heatsink Fan Cabling193
Serial Port Cabling194
Front I/O Cabling195
Power Supply Cabling196
Non-Hot-Plug Power Supply Cabling197
Flexible Slot Power Supply Cabling198
Configuration and Diagnostic Utilities200
Troubleshooting204
NMI Functionality205
Troubleshooting Resources206
System Battery Replacement207
System Battery Information208
Removing and Replacing the System Battery209
Safety, Warranty, and Regulatory Information212
Regulatory Information213
Notices for Eurasian Economic Union214
Turkey Rohs Material Content Declaration215
Ukraine Rohs Material Content Declaration216
Warranty Information217
Specifications218
Environmental Specifications219
Mechanical Specifications220
Power Supply Specifications221
HPE 350 W Gold Non-Hot-Plug Power Supply (92% Efficiency)222
HPE 500 W Flex Slot Platinum Hot-Plug Low Halogen Power Supply (94% Efficiency)223
Websites224
Support and Other Resources225
Accessing Hewlett Packard Enterprise Support226
Accessing Updates227
Customer Self Repair228
Remote Support229
Documentation Feedback230

HP ProLiant ML30 Gen10 Plus - Page 112

Table of Contents

Other manuals for HP ProLiant ML30 Gen10 Plus

Related product manuals