How to fix HunterDouglas Sonnette shades that do not roll up evenly?
It is considered normal if the roll-up on both shades is within 5/ ' of each other. If one shade rolls up tighter than another, lower and raise both shades several times. Reset the shade.
How to fix HunterDouglas Window Blinds shading that does not respond to the remote?
If your HunterDouglas Window Blinds shading does not respond to the remote, make sure that the shade is joined to a group and that the correct group number is selected. The LED on that group number will light up. You can also check which group number the shade is joined to on the remote in the PowerView App under MORE > ACCESSORIES. Check if the batteries need replacement. If the batteries are completely drained, no lights will turn on. If the batteries are running low, the inner ring buttons (open, close, right arrow, left arrow, stop) light up RED. Replace the batteries. The remote takes two CR2032 batteries.
What to do if HunterDouglas Window Blinds shade does not operate using the control button?
If your HunterDouglas Window Blinds shade isn't operating using the control button, try unplugging the power cable from the motor and plugging it back in; a blue LED should flash. Check the batteries in the battery wand, satellite battery pack, or C-size satellite battery wand to ensure they are correctly inserted and fresh. Also, verify that the power source is securely connected and the cables aren't pinched. If you have a rechargeable battery wand, ensure it's correctly positioned in the mount.
Why is the bottom rail of my HunterDouglas Window Blinds not raising or lowering completely?
If the bottom rail of your HunterDouglas Window Blinds doesn't raise or lower completely, or its fully lowered location has changed, try the following: 1. Replace the batteries in the battery wand, satellite battery pack, or C-size satellite battery wand. 2. Ensure the power source is securely connected and cables are not pinched. 3. Check for clearance between the shade and window casement on inside mounts. 4. Check if the fabric rolls up evenly into the headrail.
What to do if vanes do not open when the HunterDouglas Sonnette shade is first operated?
Make sure the shade is completely lowered. Open and close the shade several times to help open the vanes. If necessary, gently pull down on the bottom rail.
What to do if my HunterDouglas Sonnette bottom rail does not raise or lower completely?
The batteries may be low in the battery wand, satellite battery pack, or C-size satellite battery wand, so replace them. Check that the battery wand, satellite battery pack, C-size satellite battery wand, or DC power supply is securely connected to the power cable and that the cables are not pinched. Verify there is clearance between the ends of the shade and the window casement on inside mounts.
What to do if my HunterDouglas Sonnette Indoor Furnishing shade does not operate using the manual control button?
Unplug the power cable from the motor, then plug it back in. A green LED inside the manual control button housing should flash to indicate the motor has power. Check that the batteries in the battery wand, satellite battery pack, or C-size satellite battery wand are correctly inserted and fresh. Also, check that the battery wand, satellite battery pack, C-size satellite battery wand, or DC power supply is securely connected to the power cable and the cables are not pinched or caught in the headrail or installation brackets.
How to adjust the length of my HunterDouglas Sonnette Indoor Furnishing shade if it's slightly long or short?
To adjust the length of your HunterDouglas Indoor Furnishing shade, raise the shade completely until the bead chain connector touches the back of the clutch. For a shorter drop, move the bead stop two to four beads up. For a longer drop, move the bead stop two to four beads down. Note that the maximum adjustment is 1 3/4", or eight to nine beads.
What to do if my HunterDouglas Sonnette Indoor Furnishing shade hangs too low at the top?
If your HunterDouglas Indoor Furnishing shade hangs too low at the top: * For Cassette type, move the stop ball down the front of the chain to allow the shade to move further up. * For Standard/Designer Metal Bracket type, remove the shade from the brackets, lay it on a clean surface, and roll it up completely before reinstalling it.
What to do if the universal cord tensioner has climbed to the top of my HunterDouglas Sonnette Indoor Furnishing shade?
If the universal cord tensioner has climbed to the top of your HunterDouglas Indoor Furnishing shade, pull down on the spring to relieve tension and move the universal cord tensioner to the bottom of the cord loop. Ensure the cord tensioner is properly mounted.
General| Opacity | Light Filtering or Room Darkening |
|---|---|
| Fabric Options | Various colors and textures |
| UV Protection | Up to 99% UV protection |
| Control Options | Voice Control |
| Power Source | Battery Power (PowerView®) |
| Installation | Professional installation recommended |
To Next Page
