Page 4
6.2.1.6 Limitation of operating time D5 .................................................................................................. 37
6.2.2 Steam Bath Parameters (G0 - G9, G13) ....................................................................................... 38
6.2.2.1 Calibration °C Actual °C (G0) ....................................................................................................38
6.2.2.2 Hysteresis Controller (G1) .........................................................................................................38
6.2.2.3 Steam Bath °C Set Value (G2) ..................................................................................................38
6.2.2.4 Hysteresis Exhaust Fan (G3) .....................................................................................................40
6.2.2.5 Time Essence Injection (G4) ......................................................................................................40
6.2.2.6 Interval Time Essence Injection (G5) .........................................................................................40
6.2.2.7 Hysteresis Essence Injection (G6) .............................................................................................41
6.2.2.8 Hysteresis °C Max (G7) ............................................................................................................. 41
6.2.2.9 Fan Run-On Time (G8) .............................................................................................................. 41
6.2.2.10 Power Retention (G9) ..............................................................................................................41
6.2.2.11 Hysteresis Supply Fan (G13) ................................................................................................... 42
6.2.3 Steambath Operating Parameters ............................................................................................... 43
6.2.3.1 Values and Operational Conditions ............................................................................................ 50
7. Basic- DS ..........................................................................................................................................52
7.1 Basic Construction ...........................................................................................................................52
7.1.1 Basic-DS Display Unit ...................................................................................................................52
7.2 Basic-DS Main PCB ........................................................................................................................ 53
7.3 Parameter Setting with Jumpers ...................................................................................................... 53
7.3.1 Brief Description of Jumpers .........................................................................................................54
7.3.2 Explanation of Jumper Functions ..................................................................................................55
7.3.3 Description of Potentiometer ......................................................................................................... 58
7.3.3.1 Potentiometer P1 / Steam Generation Output Limitation ...........................................................58
7.3.3.2 Potentiometer P2 / Pump Run Time ..........................................................................................58
7.3.4 Potentialfree Outputs .................................................................................................................... 58
7.3.4.1 Collective Fault - Base Relay .....................................................................................................58
7.3.4.2 Humidification: ............................................................................................................................ 59
7.3.4.3 Signal Output .............................................................................................................................59
8. Fault Messages (Comfort- DS / Comfort Plus- DS und Basic- DS) .............................................. 60
9. For the Installer ................................................................................................................................63
9.1 Temperature Sensor Installation ......................................................................................................63
9.2 Temperature Sensor Connection .....................................................................................................63
9.3 Installation of Essence Injector with Peristaltic Pump (Optional) ..................................................... 64
9.3.1 Electrical Connection Peristaltic Pump* ........................................................................................ 64
9.4 Fan Installation (Optional) ................................................................................................................ 66
9.4.1 Connection for 24V Steam Bath Exhaust Fan (Optional)* ............................................................ 66
9.4.2 Connection for 24V Steam Bath Supply Fan (Optional)* .............................................................. 66
9.4.3 Connection for 230V Steam Bath Fans (Optional) ........................................................................ 67
9.5 Cabin Light Installation (Optional) ....................................................................................................67
9.5.1 Cabin Light Connection (Optional) ................................................................................................ 67
9.5.2 Connection for 230V exhaust/supply fan for steam generators type C01 and C02 ......................68
9.6 Switch/Safety Interlock ..................................................................................................................... 69
10. Potential Free Signal Output ......................................................................................................... 71
10.1 Base Relay and Signal Relay PCB ................................................................................................71
10.1.1 Base Relay and Collective Fault .................................................................................................71
10.1.2 Signal Relay PCB and Steam Bath Operation* ...........................................................................71
11. Initial Operation .............................................................................................................................. 73
12. Faults and Messages / Conditions ...............................................................................................74
To Next Page
Loading...
