b. Select the required speed and press Enter.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
The speed must be set to Set Auto Negotiation for gigabit Ethernet networks.
d. Press Cancel to backtrack through the menu hierarchy.
3. DHCP IPv4 (Default: Enabled)
a. Select Configure Network Settings > Configure DHCP > Configure DHCPIPv4.
b. Select Enable DHCP IPv4 and press Enter to enable, or press Down and select Disable DHCP IPv4 to disable.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
4. DHCP IPv6 (Default: Disabled)
a. Select Configure Network Settings > Configure DHCP > Configure DHCPIPv6.
b. Select Enable DHCP IPv6 and press Enter to enable, or press Down and select Disable DHCP IPv6 to disable.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
5. IPv4/IPv6 Address (Default: 0.0.0.0). If DHCP is disabled, set the IP address manually.
a. Select Configure Network Settings > Change IP Address.
b. Select Set IP Address IPv4 to enter the IPv4 address of the tape library. Set IP Address IPv6 to enter the IPv6 IP address (split over 4 screens).
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
6. IPv4 Subnet Mask (Default: 255.255.255.0). If DHCP IPv4 is disabled, set the IPv4 subnet mask manually.
a. Select Configure Network Settings > Change Subnet Mask > Set Subnet Mask.
b. Enter the IPv4 subnet mask.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
7. IPv6 Prefix Length (Default: 64). If DHCP IPv6 is disabled, set the IPv6 prefix length manually.
a. Select Configure Network Settings > Change Subnet Mask > Set Prefix Length.
b. Enter the IPv4 prefix length.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
8. IPv4/IPv6 Gateway (Default: 0.0.0.0). If DHCP is disabled, set the IP address manually.
a. Select Configure Network Settings > Change Gateway.
b. Select Set Gateway Address IPv4 to enter the IPv4 gateway address or Set Gateway Address IPv6 to enter the IPv6 gateway address (split over 4 screens).
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
9. Press Cancel to return to the Network Settings menu.
10. Press Cancel to return to the Configuration menu.
11. Press Cancel to return to the top menu screen.
Configuring date and time settings
Figure 1. Date and time settings
Select Configuration > Configure Library > Configure Date/Time to set the date and time on your library manually after a power disruption and when Daylight Saving Time
starts and ends. The date is set in MM/DD/YYYY format, and the time is set in 24-hour HH:MM:SS format.
The current date and time is also controlled automatically with a network-based Network Time Protocol (NTP) server. For more information, see Configuring network
settings.
Locating management functions
This section provides the menu navigation to assist with library configuration, managing, and monitoring.
Refer to the following sections:
Configuring the library Table 1
Managing the library Table 2
Monitoring the library Table 3
Managing drive Table 4
Managing cartridges Table 5
Managing security Table 6
Table 1. Configuring the library
Task Web User Interface Operator Panel
Enable auto cleaning Configure Library > Physical/Logical > Physical Settings. See Methods
of cleaning the tape drive.
Configuration > Configure Auto Cleaning. See Methods of cleaning the
tape drive.
Reset configuration
*
Not available with this interface Configuration > Set Default
To Next Page
Loading...
