Icom IC-7410

106
CONTROL COMMAND
1
2
3
4
5
6
7
8
9
10
11
12
13
15
16
17
19
20
21
14
18
14
s#HARACTERCODESETTING
Command : 1A 00
#HARACTER !3#))CODE #HARACTER !3#))CODE
A–Z 41–5A a–z 61–7A
0–9 30–39 Space 20
!21#23
$24 25
 26 < 5C
?3F " 22
’27` 60
^5E+2B
–2D
1
2A
⁄2F.2E
,2C: 3A
;3B=3D
<3C> 3E
(28) 29
[5B] 5D
{7B}7D
¦7C_5F
¯7E@40
s/PERATINGFREQUENCY
Command : 00, 03, 05
q
XXXXX
we
X
rt
XX XX
10 Hz digit: 0–9 1 Hz digit: 0–9 1 kHz digit: 0–9 100 Hz digit: 0–9 100 kHz digit: 0–9 10 kHz digit: 0–9 10 MHz digit: 0–9 1 MHz digit: 0–9 1000 MHz digit:
0 (fixed)
100 MHz digit: 0 (fixed)
s/PERATINGMODE
Command : 01, 04, 06
q
XXXX
w
q /PERATINGMODE w &ILTERSETTING
00: LSB 03: CW 07: CW-R 01: FIL1
01: USB 04: RTTY 08: RTTY-R 02: FIL2
02: AM 05: FM 03: FIL3
Filter setting (w) can be skipped with command 01
and 06. In that case, “FIL1” is automatically selected
with command 01 and the default filter setting of the
operating mode is selected with command 06.
s"ANDEDGEFREQUENCYSETTING
Command 02*, 1E 01, 1E 03
q
XXX
wertyuio!0 !1 !2
XXXXXXXXX2DXXXXXXXXXX
10 Hz digit: 0–9 1 Hz digit: 0–9 1 kHz digit: 0–9 100 Hz digit: 0–9 100 kHz digit: 0–9 10 kHz digit: 0–9 10 MHz digit: 0–9 1 MHz digit: 0–9 1000 MHz digit: 0 (fixed) 100 MHz digit: 0 (fixed) 10 Hz digit: 0–9 1 Hz digit: 0–9 1 kHz digit: 0–9 100 Hz digit: 0–9 100 kHz digit: 0–9 10 kHz digit: 0–9 10 MHz digit: 0–9 1 MHz digit: 0–9 1000 MHz digit: 0 (fixed) 100 MHz digit: 0 (fixed) Separator (fixed)
Lower edge Higher edge
Edge number*: 01–30
* Edge number setting is not necessary with com-
mand 02.
s"ANDSTACKINGREGISTER
Command : 1A 01
q
XXXX
w
q Frequency band code
#ODE &REQBAND &REQUENCYRANGEUNIT-(Z
01 1.8 1.800000– 1.999999
02 3.5 3.400000– 4.099999
03 7 6.900000– 7.499999
04 10 9.900000–10.499999
05 14 13.900000–14.499999
06 18 17.900000–18.499999
07 21 20.900000–21.499999
08 24 24.400000–25.099999
09 28 28.000000–29.999999
10 50 50.000000–54.000000
11 GENE Other than above
w Register code
#ODE 2EGISTERED.O
01 1 (latest)
02 2
03 3 (oldest)
For example, when reading the oldest contents in the
21 MHz band, the code “0703” is used.
When sending the contents, the codes, such as op-
erating frequency and operating mode*, should be
added after the register code, as shown above.
* See “Memory content setting (r to !8)” for details.
(p. 108)
D$ATACONTENTDESCRIPTION