8-8
BASIC MANUAL
8
SET MODE
The assignable key functions for Remote MIC Key
Function Description
--- No function
UP
steps*), Memory channel, repeater, or
select the next station call sign.
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
DOWN
steps*), Memory channel, repeater, or select
the previous station call sign.
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
UP
Push to increase the frequency (in the
selected Tuning Step), Memory channel,
repeater, or select the next station call
sign.
DOWN
Push to decrease the frequency (in the
selected Tuning Step), Memory channel,
repeater, or select the previous station call
sign.
VOL UP Push to increase the volume level.
VOL DOWN Push to decrease the volume level.
Hold down for 1 second to monitor signals.
CALL Push to select the Call channel mode.
•
Memory mode.
• Hold down for 1 second to copy the
DR
(DR)
In the DR screen
Home CH
Push to directly select the Home Channel
Memory) or DR screen.
LWhile in the Call channel mode, or when no
Home CH is set, an error beep sounds.
BAND/GROUP
UP
In the VFO mode
• Push to increase an operating band.
• Hold down for 1 second to recall the
Band Stacking Register contents.
In the Memory mode
Push to increase the Memory group.
BAND/GROUP
DOWN
In the VFO mode
• Push to decrease an operating band.
• Hold down for 1 second to recall the
Band Stacking Register contents.
In the Memory mode
Push to decrease the Memory group.
SCAN
• Push to start the previously selected
scan. While scanning, push to stop the
scan.
• Hold down for 1 second to open the
SCAN SELECT screen.
Function Description
Temporary
Skip
Push to set the frequency to be skipped
while scanning. The selected frequencies
are temporarily skipped for faster scanning.
SPEECH
Push to announce the frequency,
operating mode, or call sign.
L
mode, the frequency and the operating
mode are announced.
L In the DR screen, the call sign is
announced. If Simplex is selected, the
frequency is announced.
MODE
• Push to select the operating mode.
• Hold down to toggle USB and LSB, CW
and CW-R, or RTTY and RTTY-R.
Push to adjust the transmit output power.
Voice/Keyer/
RTTY Memory 1
In the SSB, AM, FM, DV, or ATV mode
• Push to transmit the voice audio
recorded on the SD card once.
• Hold down for 1 second to repeatedly
transmit the voice audio.
LThis key function can also be used on the DR
screen.
LIf the voice audio is not saved in the Voice TX
memory (T1 ~ T4), this function is disabled.
In the CW mode
• Push to transmit the Keyer memory
content once.
• Hold down for 1 second to repeatedly
transmit the memory content.
LIf the Keyer memory content (M1 ~ M4) is not
entered, this function is disabled.
In the RTTY mode
Push to transmit the RTTY memory
content once.
LIf the RTTY memory content (RT1 ~ RT4) is
not entered, this function is disabled.
Voice/Keyer/
RTTY Memory 2
Voice/Keyer/
RTTY Memory 3
Voice/Keyer/
RTTY Memory 4
T-CALL
(Only for European version.)
RX>CS
In the DV or DD mode
• Push to display the RX History list.
• Hold down for 1 second to set the last calling
station’s call sign to “TO” (destination).
TS
• Push to turn the Tuning Step function
• Hold down for 1 second to open the TS
screen.
MPAD
• Push to sequentially call up the
contents in the Memo Pads.
• Hold down for 1 second to save the
displayed contents into the Memo Pad.
SPLIT
•
• Hold down for 1 second to turn ON the
Quick Split function.
A/B
•
• Hold down for 1 second to set the
that is not displayed.
To Next Page
Loading...
