What to do if my IECHO TK4S Cutter suction force weakened and it fails to fix the materials well?
If the suction force of your IECHO Cutter is weak, and it's not holding materials properly, try these steps: * If materials are breathable, place a plastic film on their surface. * Clean the vacuum entrance filter net if it's blocked. * Check the vacuum plate and pipes for any leakage.
What to do if IECHO TK4S cannot start?
If your IECHO Cutter won't start, check the following: * Verify if the circuit breaker has tripped. * Check if the fuse is burned out. * Examine the red switch for any damage. * Use a multimeter to inspect the plug connected to the electrical box interface. * Check the circuit of the 220V power.
Why materials could not cut through with my IECHO TK4S?
If your IECHO Cutter is failing to cut through materials, consider the following: * Increase the cutting knife depth, as the knife height may not be sufficient. * Try changing to new blades. * Inspect the flatness of the cutting table; if it's uneven, contact services. * Place a piece of perforated paper on the table surface if the materials cannot be totally cut off.
How to fix IECHO TK4S Cutter when it could not cut off patterns at the corners?
If your IECHO Cutter is not cutting off patterns at the corners, try this: Open the Cutter Parameter Setting dialogue box and reset the Knife Up Compensation and Knife Down Compensation.
What to do if files sent to CutterServer failed on my IECHO TK4S Cutter?
If files are failing to send to CutterServer, use the Diagnose function within CutterServer to check the DSP version.
Lists key features of the IECHO TK4S cutting system.
Details the components of the TK4S cutting machine series.
Explains how the TK4S system processes files and controls cutting.
Provides specifications like cutting area, speed, accuracy, and power.
Describes different types of cutting heads for the TK4S machine.
Details various cutting tools available for the TK4S system.
Defines directional terms used for the TK4S machine during operation.
Lists required tools for installation and maintenance.
Specifies requirements for the machine's installation site.
Outlines requirements for the support personnel during installation.
Details electrical power specifications needed for the TK4S system.
Lists operating and storage temperature/humidity requirements.
Specifies compressed air requirements for system components.
Provides dimensions for required floor space around the machine.
Details space needed for operation, including feeding frame.
Instructions for unpacking and checking machine components.
Steps for assembling the base frame of the cutting system.
Guide for assembling the cutting beam onto the machine structure.
Procedure for installing the vacuum plates on the cutting table.
Instructions for leveling the cutting table surface accurately.
Details installing air valves and pipes for advertising applications.
Instructions for attaching the side covers for the X-axis.
Steps for connecting pneumatic lines and air valves.
Guide for connecting cables to the electric box.
Instructions for assembling main cables and towing chains.
Procedure for installing conveyor belt guide rollers.
Steps for installing the AKI device.
Explains the function of frequency converter and air control boxes.
Guide to assembling the workstation, including monitor, keyboard, mouse.
Instructions for installing the conveyor belt, including materials and steps.
Steps for properly tensioning the conveyor belt.
Details assembly of the milling support device.
Instructions for installing front and rear side covers.
Shows positions of circuit boards within the electrical box and on the machine.
Identifies danger areas on the module carriage and safety precautions.
Describes safety devices like pause and emergency stop switches.
Instructions for installing the universal cutting tool.
Procedure for installing the electrical oscillating tool.
Steps for installing the V-Cut tool.
Guide for installing the big creasing wheel holder.
Instructions for installing the PRT tool.
Pre-operation checks and requirements for the cutting system.
Detailed steps for operating the cutting machine, from power-on to finishing.
Daily checks and cleaning procedures for the cutting system.
Weekly maintenance tasks to ensure optimal performance.
Monthly checks and lubrication for machine upkeep.
Quarterly maintenance procedures for the entire machine.
Annual maintenance tasks for the cutting equipment.
Fields for product name, model, date, serial number, and QC.
Section for warranty details, customer information, and company contacts.
Information on IECHO's maintenance services and warranty.
Contains copyright, disclaimers, and company contact information.
General| Category | Cutter |
|---|---|
| Model | TK4S |
| Safety Device | Emergency Stop Button |
| Power Supply | 220V/50Hz |
| Overall Length | Unspecified |
| Laser Power | Unspecified |
| Material Fixing Method | Vacuum Table |
| Blade Material | Unspecified |
| Blade Length | Unspecified |
| Handle Material | Unspecified |
To Next Page
