IFM SD1540 - User Manual

49 pages

Save Page as PDF

To Next Page

Operating instructions

Flow meter compressed air

SD1540

80290306 / 01 09 / 2020

Main Page

Table of Contents2
Preliminary Note4
1�1 Symbols Used4
1�2 Warnings Used5
Safety Instructions5
Functions and Features6
Function6
4�1 Processing of the Measured Signals6
4�2 Switching Output7
4�3 Analogue Output8
4�4 Consumed Quantity Monitoring10
4�4�1 Meter Reading10
4�4�2 Counter Reset10
4�4�3 Consumed Quantity Monitoring Via Pulse Signals11
4�4�4 Consumed Quantity Monitoring Via Preset Counter11
4�5 Measured Value Damping12
4�6 Low Flow Cut-Off12
4�7 Simulation12
4�8 Colour of the Characters in the Display13
4�9 IO-Link14
4�9�1 Additional Functions Via IO-Link14
Installation15
5�1 Installation Location15
5�2 Installation Conditions15
5�3 Installation Position16
5�4 Installation Example Using the Process Adapter E4019517
Electrical Connection18
Operating and Display Elements20
Menu21
8�1 Process Value Display (RUN)21
8�2 Main Menu22
8�3 Extended Functions23
8�4 Submenu OUT124
8�5 Submenu OUT226
8�6 Submenu CFG28
8�7 Submenus MEM, DIS30
8�8 Submenus COLR, SIM32
Set34
Parameter Setting34
10�1 Parameter Setting in General35
10�1�1 Select Submenu35
10�1�2 Change to the Process Value Display (RUN Mode)35
10�1�3 Lock / Unlock36
10�1�4 Timeout36
10�2 Settings for Volumetric Flow Monitoring36
10�2�1 Adaptation to the Internal Pipe Diameter36
10�2�2 Limit Monitoring OUT1 or OUT2 / Hysteresis Function36
10�2�3 Limit Monitoring OUT1 or OUT2 / Window Function37
10�2�4 Analogue Signal Volumetric Flow OUT237
10�3 Settings for Consumed Quantity Monitoring37
10�3�1 Quantity Monitoring by Pulse Signal OUT1 or OUT237
10�3�2 Quantity Monitoring by Preset Counter OUT1 or OUT237
10�3�3 Manual Counter Reset38
10�3�4 Time-Controlled Counter Reset38
10�3�5 Deactivation of the Counter Reset38
10�3�6 Counter Reset Using an External Signal38
10�4 Settings for Temperature Monitoring38
10�4�1 Limit Monitoring OUT1 or OUT2 / Hysteresis Function38
10�4�2 Limit Monitoring OUT1 or OUT2 / Window Function38
10�4�3 Analogue Signal Temperature OUT239
10�5 Settings for Pressure Monitoring39
10�5�1 Limit Monitoring OUT1 or OUT2 / Hysteresis Function39
10�5�2 Limit Monitoring OUT1 or OUT2 / Window Function39
10�5�3 Analogue Signal Pressure OUT239
10�6 User Settings (Optional)40
10�6�1 Standard Display40
10�6�2 Standard Unit of Measurement for Volumetric Flow40
10�6�3 Standard Unit of Measurement for Temperature40
10�6�4 Standard Unit of Measurement for Pressure40
10�6�5 Measured Value Damping41
10�6�6 Output Logic41
10�6�7 Low Flow Cut-Off41
10�6�8 Standard Conditions41
10�6�9 Zero-Point Calibration Pressure41
10�6�10 Colour of the Characters in the Display42
10�6�11 Switch-On /Switch-Off Delay42
10�6�12 Error Behaviour of the Outputs43
10�6�13 Restore Factory Setting43
10�7 Diagnostic Functions44
10�7�1 Read Min/Max Values44
10�7�2 Simulation44
Operation45
Error Correction45
Maintenance, Repair and Disposal47
Factory Setting48

Need help?

Do you have a question about the IFM SD1540 and is the answer not in the manual?

IFM SD1540 Specifications

General

Connection Type	M12 connector
Protection class	IP67
Housing Material	Stainless steel
Measuring Range	0...40 bar
Output Signal	4...20 mA
Supply Voltage	18...30 V DC
Electrical design	PNP/NPN
Process connection	G 1/2

Related product manuals

IFM SI6600

14 pages

IFM efector 300 SI5010

13 pages

IFM LX Series

25 pages

IFM SD1540 - User Manual

Table of Contents

IFM SD1540 Specifications

Related product manuals