IFM SD1540 - Page 19

To Next Page

To Previous Page

Circuit examples:

2 x positive switching 2 x negative switching

3 BU

4 BK

2 WH

1 BN

3 BU

4 BK

2 WH

1 BN

1 x positive switching / 1 x analogue 1 x negative switching / 1 x analogue

3 BU

4 BK

2 WH

1 BN

3 BU

4 BK

2 WH

1 BN

Main Page

Table of Contents2
Preliminary Note4
1�1 Symbols Used4
1�2 Warnings Used5
Safety Instructions5
Functions and Features6
Function6
4�1 Processing of the Measured Signals6
4�2 Switching Output7
4�3 Analogue Output8
4�4 Consumed Quantity Monitoring10
4�4�1 Meter Reading10
4�4�2 Counter Reset10
4�4�3 Consumed Quantity Monitoring Via Pulse Signals11
4�4�4 Consumed Quantity Monitoring Via Preset Counter11
4�5 Measured Value Damping12
4�6 Low Flow Cut-Off12
4�7 Simulation12
4�8 Colour of the Characters in the Display13
4�9 IO-Link14
4�9�1 Additional Functions Via IO-Link14
Installation15
5�1 Installation Location15
5�2 Installation Conditions15
5�3 Installation Position16
5�4 Installation Example Using the Process Adapter E4019517
Electrical Connection18
Operating and Display Elements20
Menu21
8�1 Process Value Display (RUN)21
8�2 Main Menu22
8�3 Extended Functions23
8�4 Submenu OUT124
8�5 Submenu OUT226
8�6 Submenu CFG28
8�7 Submenus MEM, DIS30
8�8 Submenus COLR, SIM32
Set34
Parameter Setting34
10�1 Parameter Setting in General35
10�1�1 Select Submenu35
10�1�2 Change to the Process Value Display (RUN Mode)35
10�1�3 Lock / Unlock36
10�1�4 Timeout36
10�2 Settings for Volumetric Flow Monitoring36
10�2�1 Adaptation to the Internal Pipe Diameter36
10�2�2 Limit Monitoring OUT1 or OUT2 / Hysteresis Function36
10�2�3 Limit Monitoring OUT1 or OUT2 / Window Function37
10�2�4 Analogue Signal Volumetric Flow OUT237
10�3 Settings for Consumed Quantity Monitoring37
10�3�1 Quantity Monitoring by Pulse Signal OUT1 or OUT237
10�3�2 Quantity Monitoring by Preset Counter OUT1 or OUT237
10�3�3 Manual Counter Reset38
10�3�4 Time-Controlled Counter Reset38
10�3�5 Deactivation of the Counter Reset38
10�3�6 Counter Reset Using an External Signal38
10�4 Settings for Temperature Monitoring38
10�4�1 Limit Monitoring OUT1 or OUT2 / Hysteresis Function38
10�4�2 Limit Monitoring OUT1 or OUT2 / Window Function38
10�4�3 Analogue Signal Temperature OUT239
10�5 Settings for Pressure Monitoring39
10�5�1 Limit Monitoring OUT1 or OUT2 / Hysteresis Function39
10�5�2 Limit Monitoring OUT1 or OUT2 / Window Function39
10�5�3 Analogue Signal Pressure OUT239
10�6 User Settings (Optional)40
10�6�1 Standard Display40
10�6�2 Standard Unit of Measurement for Volumetric Flow40
10�6�3 Standard Unit of Measurement for Temperature40
10�6�4 Standard Unit of Measurement for Pressure40
10�6�5 Measured Value Damping41
10�6�6 Output Logic41
10�6�7 Low Flow Cut-Off41
10�6�8 Standard Conditions41
10�6�9 Zero-Point Calibration Pressure41
10�6�10 Colour of the Characters in the Display42
10�6�11 Switch-On /Switch-Off Delay42
10�6�12 Error Behaviour of the Outputs43
10�6�13 Restore Factory Setting43
10�7 Diagnostic Functions44
10�7�1 Read Min/Max Values44
10�7�2 Simulation44
Operation45
Error Correction45
Maintenance, Repair and Disposal47
Factory Setting48

IFM SD1540 - Page 19

Table of Contents

Related product manuals