Inovance MD500T75G - Page 120

7. Description of Parameters MD500 User Manual
- 120 -
Step 2: Select a proper curve for the AI terminal.
)VHOHFWVWKHFXUYHRI$,$,DQG$,IURPWKHÀYHFXUYHVUHVSHFWLYHO\&XUYHFXUYHDQGFXUYHDUHSRLQWFXUYHVVHWLQ
group F4. Curve 4 and curve 5 are 4-point curves, set in group A6.
7KH0'SURYLGHVWZR$,WHUPLQDOV$,$,$QH[WUD$,WHUPLQDO$,LVSURYLGHGE\WKH,2H[WHQVLRQFDUG
Function Code Parameter Name Setting Range Default
F4-33 AI curve selection Curve 1 (2 points, see F4-13 to F4-16)
Curve 2 (2 points, see F4-18 to F4-21)
Curve 3 (2 points, see F4-23 to F4-26)
Curve 4 (4 points, see A6-00 to A6-07)
Curve 5 (4 points, see A6-08 to A6-15)
321
Unit’s digit: AI1 curve selection
Ten’s digit: AI2 curve selection
Hundred’s digit: AI3 curve selection
F4-17 $,ÀOWHUWLPH 0.00s to 10.00s 0.10s
F4-22 $,ÀOWHUWLPH 0.00s to 10.00s 0.10s
F4-27 $,ÀOWHUWLPH 0.00s to 10.00s 0.10s
))DQG)VHWWKH$,VRIWZDUHÀOWHUWLPH,IWKHDQDORJLQSXWLVOLDEOHWRLQWHUIHUHQFHLQFUHDVHWKLVSDUDPHWHUWRVWDELOL]H
the detected analog input. But too large setting slows the response of analog detection. Set it properly based on actual conditions.
Step 3: Select a proper AI terminal as the main frequency reference setting channel.
7KH0'SURYLGHVWZR$,WHUPLQDOV$,$,$QH[WUD$,WHUPLQDO$,LVSURYLGHGE\WKH,2H[WHQVLRQFDUG
Here takes the each AI terminal as examples to show how to use the AI terminal to control the main frequency reference.
Example 1: To make the voltage input at AI1 to control the frequency reference and correspond 2 to 10 V to 10 to 40 Hz, the settings
DUHVKRZQLQWKHIROORZLQJÀJXUH
Figure 7-16 Voltage input at AI1 to control the frequency reference
Note:
2 to 10 V corresponds to 20.0% to 80.0%.
100.0% corresponds to max. frequency (F0-10 = 50.00 Hz).
AI1
F4-33
(Unit's digit) = 1
Select two-point
curve 1 for AI1
0 to 10 V
+10V
GND
Pot.
(2 kȎ)
F4-13
F4-14
Setting
20.0%
2.00
F4-15
F4-16
10.00
80.0%
F4-17 0.10
AI (V)
80.0
60.0
40.0
20.0
0.00
2.00 4.00 6.00 8.00 10.00
F4-14
0.0
F4-13 F4-15
F4-16
percentage (%)
Corresponding
Final
frequency
reference
Select main frequency
reference as final
frequency reference.
Function
Code
Select AI1 as main
frequency reference
setting channel.
F0-03 = 2
F0-07
(Unit's digit) = 0
efesotomasyon.com