Integra DTM-6 - Page 39

> Before Start > Part Names > Install > Initial Setup > Playback
Supplementary information | Advanced Setup |Others
39
En
12. 12V TRG C
Set when outputting the control signal (maximum 12 V/25 mA) through the 12V TRIGGER
OUT C jack. Different settings can be set for each input selector. You can enable power link
operation when you connect the unit and the external devices equipped with 12V trigger
input jack.
Delay Set after how many seconds the 12V trigger output will occur in
response to the unit's operation. As some devices cause a large
current when they turn on, delay the output if such devices are
connected.
Select a value between "0sec" to "3sec". (Default Value is "2sec")
BD/DVD Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BD/DVD" is selected as input for main room.
"Zone2": Output when "BD/DVD" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "BD/DVD" is selected as
input for main room or ZONE 2.
CBL/SAT Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CBL/SAT" is selected as input for main room.
"Zone2": Output when "CBL/SAT" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "CBL/SAT" is selected as
input for main room or ZONE 2.
GAME Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "GAME" is selected as input for main room.
"
Zone2 ": Output when "GAME" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "GAME" is selected as input
for main room or ZONE 2.
PC Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PC" is selected as input for main room.
"
Zone2 ": Output when "PC" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "PC" is selected as input for
main room or ZONE 2.
CD Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "CD" is selected as input for main room.
"
Zone2 ": Output when "CD" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "CD" is selected as input for
main room or ZONE 2.
TV/TAPE Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TV/TAPE" is selected as input for main room.
"Zone2": Output when "TV/TAPE" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "TV/TAPE" is selected as
input for main room or ZONE 2.
PHONO Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "PHONO" is selected as input for main room.
"Zone2": Output when "PHONO" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "PHONO" is selected as
input for main room or ZONE 2.
TUNER Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "TUNER" is selected as input for main room.
"Zone2": Output when "TUNER" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "TUNER" is selected as
input for main room or ZONE 2.
NET Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "NET" is selected as input for main room.
"
Zone2 ": Output when "NET" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "NET" is selected as input
for main room or ZONE 2.
BLUETOOTH Set the 12V trigger output setting to each input.
"Off": No output
"Main": Output when "BLUETOOTH" is selected as input for
main room.
"Z2": Output when "BLUETOOTH" is selected as input for ZONE 2.
"M/Z2 (default value)": Output when "BLUETOOTH" is selected
as input for main room or ZONE 2.
SN29403237_DTM-6_En_1707XX.book 39 ページ ２０１７年７月２７日 木曜日 午後１時３９分