JDS Uniphase SmartClass

To Next Page

To Previous Page

Chapter 11 VoIP Testing

Placing and receiving calls

SmartClass TPS User’s Guide

92 22035456, Rev 001 June 2014

Main Page

Default Chapter7
- Table of Contents7
About this Guide15
- Purpose and Scope16
- Assumptions16
- Safety and Compliance Information16
- Conventions16
Chapter 1 Getting Started19
- About the Smartclass TPS20
- Ship List20
- Configurations and Options21
  - Configurations21
  - Software Options21
- Features and Capabilities22
- Preparation for Use24
  - General Preparation24
  - Changing the AC Line Plug Fitting25
- Exploring the Front Panel26
- Exploring the Connector Panel29
- Exploring the Bottom Panel30
- Exploring the Top Panel31
- Navigating the User Interface31
- Using the Keypad34
- Customizing the User Interface35
Chapter 2 Instrument Settings37
- Managing Files38
- Managing Jobs39
- Communicating with a Mobile Device41
- Accessing the Smartclass Triple Play Services Remotely Using VNC42
- Setting the Date and Time43
  - Setting the Date43
  - Setting the Time44
- Specifying Auto Power down Settings44
- Adjusting the Screen Settings45
- Changing Keypad Setup45
  - Setting the Repeat Delay45
  - Setting the Repeat Rate45
- Specifying the Volume Level46
- Specifying International Settings46
- Managing Test Configurations47
  - Saving Test Configurations47
  - Loading a Configuration47
- Viewing Unit Revisions, Options, and Ids48
- Restoring Factory Defaults48
Chapter 3 Automated Testing49
- About the Automated Tests50
- Running the Onecheck Test50
- Running the Videocheck Test52
Chapter 4 Using the SCTPS with a Mobile Device53
- Controlling the Smartclass TPS with a Mobile Device54
- Controlling the Device Interface55
- Testing with Smartids55
- Viewing Video on a Mobile Device57
Chapter 5 Ethernet te Testing59
- About Ethernet te Testing60
- Specifying the Network Setup60
- Connecting to the Line62
- Viewing Results63
Chapter 6 DSL Testing65
- About Xdsl Testing66
  - BCM96368 Test Options66
  - BCM963168 Test Options66
- Selecting the Test Mode67
- Specifying Test Settings67
- Connecting to the Line75
- Testing the Physical Layer77
- Testing Line Quality77
- Terminating the Loop (SELT)78
Chapter 7 Data Testing79
- IP Ping Testing80
- About Data Testing80
- Connecting to the Line80
- Monitoring Pings81
- Throughput Testing82
- Tracing the Packet Route83
- Capturing Network Traffic83
Chapter 8 Wifi Testing85
- About Wifi Testing86
- Scanning for Wifi Networks87
- Emulating a Wifi End Point88
- Providing Wifi Access89
Chapter 9 HPNA Testing91
- About HPNA Testing92
- Connecting to the Line92
- Monitoring the HPNA Network92
- Testing the HPNA Network93
Chapter 10 Smartid Testing95
- About the Smartids96
- Registering Smartids97
- Configuring Smartid Settings97
- Locating Smartids98
- Testing the Home Run for VDSL Service98
- Testing the Home Network99
Chapter 11 Voip Testing101
- About Voip102
- Specifying Test Settings102
- Connecting to the Line107
- Placing and Receiving Calls107
Chapter 12 IP Video Testing111
- About IP Video Testing112
- Specifying Test Settings113
- Connecting to the Line115
- Analyzing Video Streams116
  - Terminate Mode116
  - Monitor Mode116
- Videocheck Test117
Chapter 13 Web Browser119
- About the Web Browser120
- Browsing the Web120
  - Navigating the Browser120
- Exiting the Browser122
Chapter 14 Optical Tools123
- About the Optical Tools124
- Measuring Optical Power124
Chapter 15 Copper Testing127
- About Copper Testing128
- Cord Compensation128
- Specifying Copper Settings129
- Running a Cablecheck130
- Performing a Snapshot Test130
- Running Copper Measurements131
- Placing and Receiving POTS Calls133
- Calibrating the Unit133
Chapter 16 Test Results135
- Saving Results136
  - Saving Results to a File136
  - Saving Results to a Job136
- Network Status137
- LAN Statistics138
- DSL Results138
- IP Data Results144
- Wifi Results145
  - Status145
  - Results146
- HPNA Results146
- Smartid Results147
- Voip Results148
- Video Results150
  - Stream Results150
  - Video Results151
- Optical Power Results151
- Copper Results151
Chapter 17 Stratasync157
- About Stratasync158
- Synchronizing to the Stratasync Server158
Chapter 18 Maintenance and Troubleshooting161
- Cleaning the Instrument162
- Prolonging Battery Life162
- Recharging the Battery162
- Replacing the Battery Pack163
- Updating the Software164
- Adding Options165
- Getting Technical Assistance165
- Additional Information166
- Resolving Problems166
  - Operating the Unit166
  - Performing Tests166
Appendix A Specifications177
- Physical Specifications178
- Connector Specifications178
- Environmental Specifications178
- Safety Specification178
- Power Specifications179
- Calibration179
  - Self Calibration179
  - Factory Calibration179
- Warranty Information179

JDS Uniphase SmartClass - Page 110

Table of Contents

Related product manuals