Need help?Do you have a question about the JDS Uniphase HST-3000 and is the answer not in the manual?
General| Brand | JDS Uniphase |
|---|---|
| Model | HST-3000 |
| Category | Test Equipment |
| Language | English |
Provides basic information about testing using the HST-3000 with an Ethernet SIM.
Lists and describes additional software options available for purchase for the Ethernet SIM.
Describes the physical interfaces provided by the Ethernet SIM for transmitting and receiving traffic.
Explains the different applications like Terminate, Monitor, and Thru for testing Ethernet.
Explains how to automatically detect other JDSU test instruments on the same subnet.
Details the process of launching applications, selecting test modes, and specifying settings for tests.
Explains how to examine cable states for Ethernet, IP, or TCP/UDP testing.
Details the steps involved in connecting to the link and selecting the Cable Diagnostics application.
Describes how cable measurements appear automatically on the Cable Status results display.
Explains how to turn up and troubleshoot Ethernet service on networks.
Guides the user on how to select a specific Layer 2 test for their Ethernet application.
Details the settings required to establish connectivity with another Ethernet device on a circuit.
Explains how to specify settings that characterize traffic and filter received traffic.
Allows transmitting Ethernet, IP, or TCP/UDP traffic and looping it back.
Describes how to monitor and analyze Ethernet traffic by selecting the MON/THRU application.
Explains how to turn up and troubleshoot IP services on networks.
Guides the user on how to select a specific Layer 3 IP test for their application.
Details the process of establishing an IPoE connection for IPv4 or IPv6 traffic.
Explains how to specify settings that characterize IP traffic and filter received traffic.
Explains how to verify connectivity with another Layer 3 or IP device by sending ping request packets.
Explains how to use the TCP/UDP option for testing.
Guides the user on how to select a specific Layer 4 TCP/UDP test for their application.
Details the necessary Layer 2 and Layer 3 settings required before transmitting Layer 4 traffic.
Explains how to specify Layer 4 settings before transmitting traffic over the circuit.
Guides the user on how to transmit traffic over the circuit after configuring Layer 4 settings.
Explains how to transmit and analyze multiple streams of traffic.
Guides the user on selecting a Layer 2, Layer 3, or Layer 4 streams test.
Details how to specify traffic characteristics, enable streams, and configure traffic loads.
Explains how to specify Layer 2, Layer 3, and Layer 4 characteristics for each stream.
Guides the user on how to transmit streams over the link after enabling and configuring them.
Describes the automated RFC 2544 testing feature.
Explains the throughput test used to determine the highest possible bandwidth with no lost frames.
Explains the latency test, measuring delay after throughput is determined.
Explains the packet jitter test, measuring packet delay variation.
Details understanding settings and navigating menus for the Classic RFC 2544 test.
Guides on launching applications and specifying RFC 2544 modes for the Expert test.
Explains how to view the stored text file and PDF of test results.
Explains the SAMComplete functionality for Ethernet Service Activation testing.
Guides on enabling the SAMComplete test before specifying settings.
Details how to specify settings for SAMComplete tests, varying by application type.
Guides on running the SAMComplete test after specifying all settings.
Describes how results are updated on screen and categories available for viewing.
Describes common situations encountered during testing and their resolutions.
Describes test result categories and how to view them.
Displays non-zero error results, out-of-specification, or key informational results for quick access.
Shows measurements associated with running cable diagnostics on a link.
Lists link statistics such as average frame rate and round trip delay measurements.
Lists error statistics such as FCS errors, runts, and out of sequence frames.
Provides electrical specifications for 10/100/1000 Base-TX and 100 Mb/s interfaces.
Details specifications for JDSU-recommended SFPs, complying with MSA.
States the unit's operating temperature range.
To Next Page
