Jet ZH Series - User Manual

Questions and Answers

D
Dana ChandlerAug 13, 2025
Why won't my Jet ZH start?
- J
  Jamie BoothAug 13, 2025
  There are several reasons why your Jet Lathe might not be starting. It could be due to: * No electrical power or incorrect wiring: Verify the incoming power, main leads, and that the main switch is on. * Emergency stop switch: Rotate the switch clockwise to release it. * Open end gear cover: Close the cover. * Blown fuse: Replace the fuse in the main electrical box or reset the circuit breaker at the power source. * Defective components: Have an electrician test the on/off switch, motor, or cable. * Faulty foot brake switch: Check and replace it if needed. * Tripped thermal relay: Reset it. If it trips frequently, increase the amp setting.
T
Thomas YoungAug 16, 2025
Why is my Jet Lathe vibrating so much?
- H
  Henry WilliamsAug 16, 2025
  Excessive vibration in your Jet Lathe can stem from several issues: * Unbalanced workpiece: Reduce the spindle speed. * Workpiece deflection: Adjust the chucking length or diameter, and use support on the tailstock end. * Tool deflection: Reduce the tool length. * Backlash: Adjust backlash on slide ways/gibs. * Dry slides: Properly lubricate the slides/ways. * Dull tool: Resharpen or replace the tool. * High chip load: Reduce the depth of cut or feed rate. * Misaligned belts: Inspect and correct the belts. * Spindle bearings: Adjust the bearings.
R
ronaldroseAug 20, 2025
What to do if my Jet ZH Lathe is overheating?
- B
  Brian DuarteAug 20, 2025
  If your Jet Lathe is overheating, it's likely due to bogging down in the cut. This can be caused by an excessive feed rate or depth of cut. Try decreasing the feed rate or depth of cut.
J
Jessica LunaAug 25, 2025
Why does my Jet ZH Lathe spindle lack turning power or starts slowly?
- A
  Angel HuffAug 25, 2025
  If the spindle on your Jet Lathe lacks turning power or starts up slowly, it could be due to: * A slipping friction clutch: Adjust the clutch. * Slipping belts: Tighten the belts.
M
Mary JonesAug 27, 2025
Why is my Jet Lathe turning a taper?
- C
  Cassandra JohnsonAug 27, 2025
  If your Jet Lathe is turning a taper, it's likely due to: * Misalignment: The tailstock is not aligned with the headstock, so align the tailstock. * Twisted bed: The lathe bed is twisted, so correct this by leveling the lathe.
C
Curtis HughesAug 31, 2025
What to do if tool tip burns on Jet Lathe?
- C
  christianvaughnAug 31, 2025
  If the tool tip is burning on your Jet Lathe, it could be caused by: * Cutting speed: The cutting speed is too high, so reduce the speed. * Dull tool: The tool is dull, so resharpen or replace it.
C
charlesnunezSep 4, 2025
Why is it difficult to move carriage, cross slide or compound rest on my Jet ZH?
- S
  shanehendricksSep 4, 2025
  If the carriage, cross slide, or compound rest on your Jet Lathe is difficult to move, it could be due to: * Tightened carriage lock: Release the carriage lock. * Tight gibs: Adjust the gibs using the gib screws. * Debris or dryness: Clean the bed ways and verify they are being lubricated properly.
E
Erika RoweSep 8, 2025
Why is there no automatic power feed on my Jet Lathe?
- M
  Mary VaughnSep 8, 2025
  If there is no automatic power feed on your Jet Lathe, the shear pin is likely broken. Replace the shear pin.