Jet ZH Series User Manual

6
4.0 Specifications
Model Number................................................................................ GH-2680ZH ......................................... GH-26120ZH
Stock Number ....................................................................................... 321860 .................................................. 321890
General Capacities:
Maximum Swing over Bed ......................................................... 26” (660mm) ......................................... 26” (660mm)
Maximum Swing over Cross Slide ....................................... 16-1/2” (420mm) ................................... 16-1/2” (420mm)
Maximum Swing Through Gap .................................................. 34” (870mm) ......................................... 34” (870mm)
Length of Gap ........................................................................ 7-7/8” (200mm) .................................... 7-7/8” (200 mm)
Distance between Centers ...................................................... 80” (2030mm) ..................................... 120” (3050mm)
Width of Bed .............................................................................. 16” (405mm) ......................................... 16” (405mm)
Motors and Electrical:
Main Motor.............................................................................TEFC Induction ..................................... TEFC Induction
Horsepower ....................................................................... 10 HP (7.5kW) ...................................... 10 HP (7.5kW)
Phase ............................................................................................... 3 PH ...................................................... 3 PH
Voltage ............................................................ 230/460V (prewired 230V) .................... 230/460V (prewired 230V)
Full Load Amps ........................................................................ 25.4/12.7A .............................................25.4/12.7A
Cycle ............................................................................................... 60 Hz .................................................... 60 Hz
Feed Motor ...................................................................................... Induction ............................................... Induction
Horsepower ................................................................................... 1/2 HP ................................................... 1/2 HP
Phase ............................................................................................... 3 PH ...................................................... 3 PH
Voltage ............................................................ 230/460V (prewired 230V) .................... 230/460V (prewired 230V)
Full Load Amps ........................................................................ 2.85/1.65A .............................................2.85/1.65A
Cycle ............................................................................................... 60 Hz .................................................... 60 Hz
Coolant Pump Motor ........................................................................ Induction ............................................... Induction
Horsepower ................................................................................... 1/8 HP ................................................... 1/8 HP
Phase ............................................................................................... 3 PH ...................................................... 3 PH
Voltage ............................................................ 230/460V (prewired 230V) .................... 230/460V (prewired 230V)
Full Load Amps ........................................................................ 0.54/0.27A .............................................0.54/0.27A
Cycle ............................................................................................... 60 Hz .................................................... 60 Hz
Power Transmission ..................................................................... v-belt (x 4) ............................................. v-belt (x 4)
Controls circuit ............................................................................... 110V A.C. ..............................................110V A.C.
Lamp circuit ..................................................................................... 24V A.C. ...............................................24V A.C.
Indicators circuit ............................................................................. 110V A.C. ............................................. 110V A.C.
Headstock and Spindle:
Spindle Bore .......................................................................... 4-1/8” (105mm) ..................................... 4-1/8” (105mm)
Spindle Mount.......................................................................... D1-8 Camlock ....................................... D1-8 Camlock
Spindle Taper with Sleeve ....................................... 113mm Dia. 1:20 / MT-5 ....................... 113mm Dia. 1:20 / MT-5
Number of Spindle Speeds ........................................................................ 12 .......................................................... 12
Range of Spindle Speeds .....................................................36 to 1600 RPM .................................... 36 to 1600 RPM
Distance Floor to Spindle Center (approx.) .............................................. 46” ......................................................... 46”
3-Jaw Scroll Chuck:
Load Capacity........................................................................ 661 lb (300 kg) ...................................... 661 lb (300 kg)
Inside Diameter ............................................................ 5-11/16” (145mm) ................................ 5-11/16” (145 mm)
Carriage:
Maximum Compound Rest Travel ........................................ 5-1/2” (140 mm) .................................... 5-1/2” (140 mm)
Maximum Compound Rest Swivel ................................................ +/- 90 deg. .............................................
+/- 90 deg.
Maximum Cross Slide Travel ............................................ 14-1/16” (358 mm) ................................ 14-1/16” (358 mm)
Maximum Carriage Travel ....................................................... 65” (1650mm) .............................. 106-1/4” (2700 mm)

Jet ZH Series Specifications

General

Brand	Jet
Model	ZH Series
Category	Lathe
Language	English