– 46 –
32 Effective condition Effective condition of reverse feed stitching on the way U 0/1 55
of reverse feed 0 : Function is not operative when the sewing machine stops.
stitching on the 1 : Function is operative when the sewing machine stops.
way when the
sewing machine
is stopping.
33 Thread trimming Thread trimming function by reverse feed stitching on the way U 0/1 55
function by 0 : Automatic thread trimming function after completion of
reverse feed reverse feed stitching on the way is not operative.
stitching on 1 : Automatic thread trimming after completion of reverse
the way feed s titching on the way is performed.
35 Number of Lowest speed by pedal U 20 to 400 62
rotation at a (rpm)
low speed
36 Number of Thread trimming speed U 20 to 250
rotation of (Caution) Do not change the set value. (rpm)
thread When it is changed, the sewing machine is
trimming apt to be broken.
37 Number of Sewing speed at the start of sewing (soft-start) U 150 to 5500 52
rotation of (rpm)
soft-start
38 One-shot One-shot speed (The max. value depends on the number U 200 to MAX 56
speed of rotation of the sewing machine head.) (rpm)
39 Pedal stroke at Position where the sewing machine starts rotating from U 1.0 to 5.0 57
the start of pedal neutral position (0.1mm)
rotation (Pedal stroke)
40 Low speed Position where the sewing machine starts accelerating U 1.0 to 10.0 57
section of from pedal neutral position (0.1mm)
pedal (Pedal stroke)
41 Starting position Position where the cloth presser starts lifting from pedal
U -6.0 to -1.0 57
of lifting presser neutral position (0.1mm)
foot by pedal (Pedal stroke)
42 Starting position Adjustment of the stroke from the pedal neutral position to U 0.8 to 5.0 57
of lowering the position where the presser lifter begins to come down (0.1mm)
presser foot (When the neutral auto presser lifting function is used)
(Pedal stroke)
43 Pedal stroke 2 Position 2 where the thread trimming starts from pedal
U -6.0 to -1.0 57
for starting neutral position (When the function of lifting presser foot (0.1mm)
thread trimming by pedal is provided.)
(Pedal stroke)
44 Pedal stroke for Position where the sewing machin reaches its highest U 1.0 to 15.0 58
reaching the sewing speed from pedal neutral position (0.1mm)
maximum number (Pedal stroke)
of rotation
45 Compensation Compensation value of the pedal sensor U -15 to 15 58
of neutral point
of the pedal
46 Auto-lifter Auto-lifter selection U 0/1
selecting 0 : Solenoid drive system
function 1 : Pneumatic drive system
47 Holding time of Limitation time of waiting for lifting solenoid type auto-lifter U 10 to 600 58
lifting auto-lifter device (second)
48 Pedal stroke 1 Position where thread trimming starts from pedal neutral U -6.0 to -1.0 58
for starting position (Standard pedal) (Pedal stroke) (0.1mm)
thread trimming
49 Lowering time Lowering time of presser foot after the pedal has been U 0 to 250 60
of presser foot depressed. (10ms)
(Start of rotation of the sewing machine is delayed during
this time.)
No. Item Description Start level Setting range
Indication of
function setting
Ref.
page
∗ Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(Descriptions of setting in this list are the standard values at the time of delivery of DDL-9000A.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
∗
To Next Page
Loading...
Need help?
General
