JUKI SC-910N Engineer's Manual

– 47 –
51 Compensation Compensation of starting the solenoid for reverse feed U -36 to 36 58
of solenoid-on stitching when reverse feed stitching at the start of (10°)
timing of reverse sewing is performed.
feed stitching at
the start of
sewing
52 Compensation Compensation of releasing the solenoid for reverse feed U -36 to 36 58
of solenoid-off stitching when reverse feed stitching at the start of sewing (10°)
timing of reverse is performed.
feed stitching at
the start of
sewing
53 Compensation Compensation of releasing the solenoid for reverse feed U -36 to 36 59
of solenoid-off stitching when reverse feed stitching at the end of sewing (10°)
timing of reverse is performed.
feed stitching at
the end of
sewing
55 Foot lift after Function of lifting presser foot at the time of (after) thread U 0/1 59
thread trimming trimming
0 : Not provided with the function of lifting presser foot
after thread trimming
1 : Provided with the function of lifting presser foot
automatically after thread trimming
56 Reverse Function of reverse revolution to lift the needle at the time U 0/1 59
revolution to lift of (after) thread trimming
the needle after 0 : Not provided with the function of reverse revolution
thread trimming to lift the needle after thread trimming
1 : Provided with the function of reverse revolution to
lift the needle after thread trimming
57 Bobbin thread Function of detecting bobbin thread remaining amount at the U 0/1 59
remaining time of (after) thread trimming
amount 0 : Not provided with the function of detecting bobbin thread
detection remainingamount
function 1 : Provided with the function of detecting bobbin thread
remaining amount
58 Function of Function of holding predetermined upper/lower position of U 0 to 1 59
holding the needle bar
predetermined 0 : Not provided with the function of holding predetermined
upper/lower upper/lower position of the needle bar
position of the 1 : Provided with the function of holding predetermined
needle bar upper/lower of the needle bar
59 Function of This function can specify the sewing speed of reverse feed U 0/1 59
Auto/Manual stitching at the start of sewing.
change-over of 0 : The speed will depend on the manual operation by
reverse feed pedal, etc.
stitching at the 1 : The speed will depend on the specified reverse feed
start of sewing stitching speed (No. 8).
60 Function of stop Function at the time of completion of reverse feed stitching at the U 0/1 60
immediately start of sewing
after reverse 0 : Not provided with the function of temporary stop of the
feed stitching at sewing machine at the time of completion of reverse feed
the start of stitching at the start of sewing
sewing 1 : Provided with the function of temporary stop of the sewing
machine at the time of completion of reverse feed stitching
at the start of sewing.
61 Function of starting Function of starting prohibition of the sewing machine by U 0/1 59
prohibition of detection of bobbin thread remaining amount
the sewing 0 : This function does not stop the sewing machine when
tmachine by counting is out (-1 or less).
detection of 1 : This function stops the sewing machine when counting
bobbin thread is out (-1 or less).
remaining amount
64 Change-over Initial speed when starting condensation stitch or EBT U 0 to 250 62
speed of (rpm)
condensation
stitch or EBT
(end back tack)
65 On-timing of Starting (compensation) timing of solenoid for compensation U -36 to 0 54
solenoid for stitch : -1 (10°)
condensation Compensation value of starting the solenoid when
stitch (when condensation stitch is performed by 1 stitch.
condensation
stitch is performed
by 1 stitch.)
3
5
5
-
6
5
0
7
5
0
8
5
0
9
5
1
0
6
0
1
6
1
4
6
0
1
8
5
6
5
-
1
No. Item Description Start level Setting range
Indication of
function setting
Ref.
page
1
1
5
8
-
2
5
5
-
5
5
1

JUKI SC-910N Specifications

General

Brand	JUKI
Model	SC-910N
Category	Sewing Machine
Language	English