0
Deep Color
Setting Values Description
AUTO Set to this value when a “Deep
Color” device
is connected.
OFF Set to this value when the video image is
distorted, or colors are unnatural.
0
HDMI RGB OUTPUT RANGE
Setting Values Description
STANDARD Set to this value for standard uses.
ENHANCED Set to this value when the black and white
parts of the video image are not distinct.
Memo :
0
This is available when connected to a DVI device that only
supports RGB input.
0
HDMI --> DVI COLOR
Setting Values Description
AUTO Value is set automatically according to the
monitor.
RGB FIX Use this setting when video images are not
correctly displayed on the monitor.
Memo :
0
This is available when the
“x.v.Color” setting is set to “OFF”.
When the “x.v.Color” setting is set to “AUTO”, this setting will
be set to “AUTO” automatically.
0
Change this setting when no video image appears while
connected to a DVI device.
0
HDMI AUDIO OUTPUT
Setting Values Description
OFF Use this setting if you do not want to send
audio output from the HDMI cable.
ON Use this setting to send audio output from
the HDMI cable.
HDMI-CEC
For setting the HDMI-CEC operation from the connected device.
Setting Values Description
OFF Disables HDMI-CEC.
ON Enables HDMI-CEC.
SDI/COMPONENT OUTPUT
For setting the resolution of video output from the [SDI OUT] and
[COMPONENT VIDEO OUT] terminals.
Setting Values Description
480i
(SR-HD2700U)
576i
(SR-HD2700E)
Sets output to “480i” or “576i”.
480p
(SR-HD2700U)
576p
(SR-HD2700E)
Sets output to “480p” or “576p”.
720p Sets output to “720p”.
1080i Sets output to “1080i”.
Memo :
0
When the resolution is set to “720p”, videos are output at
“1080i” other than those recorded at “720p” even though
“720p” is shown on the display.
0
This unit does not support component output at
“1080p”. To
output at “1080p”, do so via HDMI connection.
0
If “VIDEO PRIORITY MODE” is set to “HDMI
”, the unit will
output at “480i” or “576i” regardless of the current setting.
0
If “VIDEO PRIORITY MODE” is set to “SDI/COMPONENT
”,
or when an HDMI connection is used, DVD videos and BDMV
will be output at “480i” or “576i” even if “720p” or “1080i” has
been set.
0
The aspect ratio of video/S-video output changes according
to
the component output setting. As such, there may be cases
where the aspect ratio of the video/S-video output is different
from the predefined setting of the content.
VIDEO INPUT SETTING
Choose a setting according to the video terminal to be
connected when an external analog input terminal is used.
Setting Values Description
VIDEO Use this setting when connecting via the
video (BNC) terminal.
S-VIDEO Use this setting when connecting via the S-
video (black) terminal.
Note :
0
Perform
“VIDEO INPUT SETTING” after selecting L-1 as the
input.
If “VIDEO INPUT SETTING” is performed with the input set to
other than L-1, the output image may switch from the original
input signal to the L-1 input signal. In this case, select L-1 as
the input and perform the setting again.
HDCP
For setting the output of copyright-free contents to devices that
do not support HDCP.
Setting Values Description
FIXED Encrypts copyright-free contents during
playback.
AUTO Does not encrypt copyright-free contents
during playback.
Memo :
0
If “HDCP
” is set to “AUTO” while a device incompatible with
HDCP is used, images may appear distorted. Operate as
follows if the images are distorted.
Press and hold the “0” button on the remote control for 5
seconds to set “HDCP” to “AUTO”.
Setting Menu List
91
Settings Menu
To Next Page
Loading...
