KEB COMBIVERT F5 MULTI

1 1
Name: Basis
KEB COMBIVERT F5-M / S
8
18.05.04
Introduction
General
© KEB Antriebstechnik, 2002
All Rights reserved
Chapter Section Page Date
4.2.2 Passwords...........................................................................4.2.4
4.2.3 Changing of Password Level............................................... 4.2.4
4.3 CP-Parameter ..................................................................................... 4.3.3
4.3.1 Operation in CP-Mode......................................................... 4.3.3
4.3.2 Factory Setting .................................................................... 4.3.4
4.3.3 Password Input.................................................................... 4.3.6
4.3.4 Operating Display................................................................ 4.3.6
4.3.5 Basic Adjustment of the Drive ............................................. 4.3.8
4.3.6 Special Adjustments.......................................................... 4.3.14
4.3.7 Factory Settings................................................................. 4.3.22
4.4 Drive-Mode.......................................................................................... 4.4.3
4.4.1 Adjustment Possibilities ...................................................... 4.4.3
4.4.2 Display and Keyboard ......................................................... 4.4.3
4.4.3 Setpoint Display /Setpoint Input .......................................... 4.4.3
4.4.4 Rotation Setting...................................................................4.4.4
4.4.5 Start / Stop / Run .................................................................4.4.4
4.4.6 Leaving the Drive-Mode ...................................................... 4.4.5
4.4.7 Further Settings................................................................... 4.4.5
5. Parameter ............................................................................................... 5.1.3
5.1 Parameter............................................................................................5.1.3
5.1.1 Parameter Groups ............................................................... 5.1.3
5.1.2 F5-MULTI Control ................................................................ 5.1.4
5.1.3 F5-SERVO Control .............................................................. 5.1.4
5.1.4 F5-A-SERVO Control .......................................................... 5.1.4
5.1.5 Parameter Listing ................................................................ 5.1.5
6. Functional Description ......................................................................... 6.1.3
6.1 Operating and Unit Data .................................................................... 6.1.3
6.1.1 Summary of ru-Parameter.................................................... 6.1.3
6.1.2 Summary of In-Parameter .................................................... 6.1.4
6.1.3 Summary of Sy-Parameter................................................... 6.1.4
6.1.4 Explanation to Parameter Description ................................. 6.1.5
6.1.5 Description of ru-Parameter................................................. 6.1.6
6.1.6 Description of In-Parameter ............................................... 6.1.21
6.1.7 Description of Sy (System) - Parameter ............................. 6.1.25
6.2 Analog In- and Outputs...................................................................... 6.2.3
6.2.1 Summary Description Analog Inputs ................................... 6.2.3
6.2.2 Interface Selection (An.0; An.10) .........................................6.2.4
6.2.4 Save Mode (An.2; An.12; An.22).......................................... 6.2.5
6.2.5 Input Selection (An.3; An.13; An.23) .................................... 6.2.5
6.2.3 Interference Suppression Filter (An.1; An.11; An.21) ........... 6.2.5
6.2.6 Zero Point Hysteresis (An.4; An.14; An.24).......................... 6.2.6
6.2.7 Amplifier of the Input Characterstic...................................... 6.2.7
6.2.8 Lower and Upper Limit ........................................................ 6.2.8
6.2.9 Selection Set Point-/Auxiliary Input (An.30)......................... 6.2.9
6.2.10 Brief Description Analog Outputs ...................................... 6.2.10
6.2.11 Output signals ................................................................... 6.2.11