Keithley 617 User Manual

3.10.1
3.10.2
3.10.3
3.10.4
3.10.5
3.10.6
3.10.7
3.10.8
3.10.9
3.10.10
3.10.11
3.10.12
3.10.13
3.10.14
3.10.15
3.10.16
3.10.17
3.10.18
3.11
3.11.1
3.11.2
3.11.3
3.12
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5.1
5.2
5.3
5.4
5.5
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.5.7
Execute(X) ...... .................
Function (F) ........................
Range(R)
..........................
Zero Correct and Zero Check (Z and C)
Baseline Suppression (N) .............
Display Mode CD).
..................
Reading Mode (B) ............ ......
Data Store Mode ...................
Voltage Source Value (V) .............
Voltage Source Operate (0) ..........
Calibration Value (A). ...............
Non-Volatile Memory Storage (L) .....
Data Format (G) ....................
Trigger Mode (T) ...................
SRQ Mode (M) and Status Byte Format
EOI and Bus Hold-Off Modes (K) ......
Terminator(Y) .....................
Status(u) .........................
Front Panel Messages ..................
BusError.. ........................
NumberError ......................
Trigger Overrun Error ...............
Bus Data Transmission Times ...........
SECTION 4-APPLICATIONS
Introduction .................................................................
Insulation Resistance Measurements.
.............................................
HighImpedanceVoItmeter
.....................................................
Low-Level Leakage Current Measurements
........................................
DiodeCharacterization
........................................................
CapacitorLeakageMeasurements
...............................................
CapacitanceMeasurement
......................................................
Voltage Coefficients of High-Megohm Resistors
....................................
Static Charge Detection ........................................................
Using the Model 617 with External Voltage Sources
.................................
SECTION 5-PERFORMANCE VERIFICATION
Introduction ..............................
Environmental Conditions ..................
Initial Conditions ..........................
Recommended Test Equipment ...............
Verification Procedure ......................
Input Current Verification .................
Amps Verification .......................
Coulombs Verification. ...................
Volts Verification ........................
Ohms Verification .......................
Ohms Verification (200M0 and Gfl Ranges)
Voltage Source Verification. ...............
...........
...........
...........
...........
...........
...........
...........
...........
...........
...........
..........
..........
..........
..........
..........
..........
..........
..........
..............
..............
..............
..............
.............
..............
..............
..............
.............
.............
.............
.............
.............
.............
.............
.............
.............
3-18
3-18
3-20
3-21
3-22
3-22
3-23
3-23
3-24
3-25
3-25
3-26
3-26
3-27
3-28
3-30
3-31
3-31
3-34
3-34
3-35
3-35
3-36
4-l
4-l
4-5
4-5
4-7
4-8
4-E
4-10
4-12
4-12
5-l
5-l
5-l
5-l
5-2
5-2
5-2
5-3
5-5
5-6
5-6
5-8
iii

Keithley 617 Specifications

General

Brand	Keithley
Model	617
Category	Measuring Instruments
Language	English