Kramer VS-88H2A

Kramer Electronics Ltd.
VS-88H2A – Protocol 3000
66
Function
Description
Syntax
Parameters/Attributes
Example
AUD?
LEGACY COMMAND.
Get audio switch state.
When AFV
switching mode is
active, this command
cannot switch video.
COMMAND
#AUD?out_id<CR>
#AUD?*<CR>
FEEDBACK
~nn@AUDin>out_id<CR><LF>
~nn@AUDin>1,in>2,…<CR><LF>
in – Input number
1 – HDMI IN 1
2 – HDMI IN 2
3 – HDMI IN 3
4 – HDMI IN 4
5 – HDMI IN 5
6 – HDMI IN 6
7 – HDMI IN 7
8 – HDMI IN 8
9 – Analog IN 1
10 – Analog IN 2
11 – Analog IN 3
12– Analog IN 4
13– Analog IN 5
14– Analog IN 6
15– Analog IN 7
16– Analog IN 8
> – Connection character between
in and out parameters
out_id – Output number
* – All outputs
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
9 – Analog OUT 1
10 – Analog OUT 2
11 – Analog OUT 3
12– Analog OUT 4
13– Analog OUT 5
14– Analog OUT 6
15– Analog OUT 7
16– Analog OUT 8
Get audio switch state for
HDMI OUT 3:
#AUD?3<CR>
AV
Switch audio and
video.
COMMAND
#AVin>out_id,in>out_id,…<CR>
FEEDBACK
~nn@AVin>out_id,in>out_id,…<CR><LF>
in – Number that indicates the
specific input:
0 – disconnect output
1 – HDMI IN 1
2 – HDMI IN 2
3 – HDMI IN 3
4 – HDMI IN 4
5 – HDMI IN 5
6 – HDMI IN 6
7 – HDMI IN 7
8 – HDMI IN 8
> – Connection character between
in and out parameters
out_id –Output number
* – All outputs
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
Switch IN 1 to OUT 4:
#AV1>4<CR>
AV-SW-
MODE
Set input auto switch
mode (per output).
COMMAND
#AV-SW-MODElayer_type,out_index,connection_mode<CR>
FEEDBACK
~nn@AV-SW-MODElayer_type,out_index,connection_mode<CR><L
F>
layer_type – Number that
indicates the signal type:
1 – Video
out_index – Number that
indicates the specific output:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
connection_mode – Connection
mode
0 – manual
1 – priority switch
2 – last connected switch
Set input auto switch mode
(per output) for HDMI 1 to
manual:
#AV-SW-MODE1,1,0<CR>