Krone Comprima F 155 - Appendix;Circuit Diagrams of the Hydraulic System; Appendix; Circuit Diagrams of the Hydraulic System

Contents
RP701-10 , RP701-11 , RP701-20 , RP701-21 , RP701-30 , RP701-31 , RP701-40 , RP701-41 , RP701-51
Comfort 1.0_en 1
1 Connecting the terminal............................................................................................................ 3
1.1 Connecting KRONE Beta II terminal ........................................................................................... 3
1.2 Connecting the KRONE ISOBUS terminal (CCI200, DELTA) .................................................... 5
1.3 Connecting the KRONE ISOBUS terminal (CCI1200)................................................................ 7
1.4 Connecting foreign ISOBUS terminal .......................................................................................... 9
2 KRONE BETA II terminal ......................................................................................................... 11
2.1 ISOBUS Shortcut Button not available ...................................................................................... 11
2.2 Switching terminal on/off............................................................................................................ 12
2.3 Design of display ....................................................................................................................... 13
3 KRONE ISOBUS terminal (CCI200, DELTA).......................................................................... 14
3.1 ISOBUS Shortcut Button (ISB) .................................................................................................. 15
3.2 Touchable display...................................................................................................................... 16
3.3 Switching terminal on/off............................................................................................................ 17
3.4 Design of display ....................................................................................................................... 18
4 KRONE ISOBUS terminal (CCI1200)...................................................................................... 19
4.1 Touchable display...................................................................................................................... 19
4.2 Switching terminal on/off............................................................................................................ 20
4.3 Design of display ....................................................................................................................... 21
4.4 Design of the KRONE machine application ............................................................................... 21
5 Foreign ISOBUS terminal........................................................................................................ 23
5.1 ISOBUS Shortcut Button not available ...................................................................................... 23
5.2 Varying functions to KRONE ISOBUS terminal ......................................................................... 24
6 Terminal machine functions ................................................................................................... 25
6.1 Status line .................................................................................................................................. 25
6.2 Keys........................................................................................................................................... 26
6.3 Displays on the working screen ................................................................................................. 28
6.4 Accessing the working screen ................................................................................................... 30
6.5 Automatic call of the Road travel screen ................................................................................... 30
6.6 Adjusting bale diameter ............................................................................................................. 31
6.7 Adjusting the baling pressure .................................................................................................... 32
6.8 Operating the hydraulic blade group control system ................................................................. 32
7 Terminal menus ....................................................................................................................... 34
7.1 Menu Structure .......................................................................................................................... 34
7.2 Recurring icons.......................................................................................................................... 35
7.3 Selecting a menu Level ............................................................................................................. 36
7.4 Selecting a menu ....................................................................................................................... 36
7.5 Changing value.......................................................................................................................... 37
7.6 Changing mode ......................................................................................................................... 38
7.7 Tying in the menu level.............................................................................................................. 39
7.8 Menu1 “Number of net layers” (net wrapping) .......................................................................... 40
7.9 Menu 1 “Number of film layers” (chamber film wrapping).......................................................... 41
7.10 Menu 2 "Number of twine layers" (twine tying) .......................................................................... 41
7.11 Menu 3 “Advance signalling” ..................................................................................................... 42
7.12 Menu 4 “Tying start delay” (net wrapping) ................................................................................. 43
7.13 Menu 4 "Tying start delay" (twine tying)..................................................................................... 44
7.14 Menu 4 “Tying start delay” (chamber film wrapping) ................................................................. 45
7.15 Menu 5 “Bale diameter” ............................................................................................................. 46
7.16 Menu7 “Sensitivity of direction display” .................................................................................... 47
7.17 Menu 8 "Select type of tying" (for the "Net wrapping and twine tying" version) ......................... 48
7.18 Menu 8 “Type of tying” (for the “Net and chamber film wrapping” version) ............................... 48
7.19 Menu9 “Filling correction” ......................................................................................................... 49
7.20 Menu 10 "Manual operation" (for the "Net wrapping" version)................................................... 50
7.21 Menu 10 "Manual operation" (for the "Net wrapping and twine tying" version).......................... 51
7.22 Menu 10 “Manual operation” (for the “Net and chamber film wrapping” version) ...................... 52
7.23 Menu 13 "Counters"................................................................................................................... 53
7.23.1 Menu 13-1 “Customer counter”.................................................................................................. 54
7.23.2 Menu 13-2 "Total counter" ......................................................................................................... 56