Why does a fax I sent appear blank when received from my Kyocera All in One Printer?
A fax you sent might appear blank when received from your Kyocera All in One Printer because the original was placed upside down. Place the original in the correct orientation.
What to do if my Kyocera FS-C1020MFP+ All in One Printer has a paper jam frequently?
If your Kyocera All in One Printer experiences frequent paper jams, adjust the paper guides to remove any gaps between the paper and the guides. Avoid printing on both sides of paper when printing images that contain large areas of solid color. Use supported paper types. Load paper only to the upper limit markings on the paper guide. Ensure the friction pad, paper feed roller, and registration roller are clean.
What to do if my Kyocera FS-C1020MFP+ All in One Printer photocopied paper is dirty?
If the photocopied paper from your Kyocera All in One Printer is dirty, adjust the image density because it might be too high. Avoid touching printed surfaces immediately after copying to allow the toner to dry. Ensure the exposure glass or ADF is clean. Before placing originals on the exposure glass, ensure that toner or correction fluid is dry.
What to do if my Kyocera All in One Printer prints multiple sheets of paper at once?
If your Kyocera All in One Printer feeds multiple sheets of paper at one time, fan the paper well before loading it, and make sure the edges are even. Ensure the paper guides are in the correct position and that you're using supported paper types. Load paper only as high as the upper limit markings on the paper guide. Also, ensure the friction pad, paper feed roller, or registration roller is clean and avoid adding paper while there is still some left in the tray.
Why is the background of received images dirty, or images from the rear side of the originals are visible on my Kyocera All in One Printer?
The background of received images might be dirty, or images from the rear side of the originals are visible on your Kyocera All in One Printer because the image density is too high. Adjust the image density.
What to do if my Kyocera All in One Printer has run out of the indicated toner?
If your Kyocera All in One Printer has run out of the indicated toner, press [No] to cancel the job and replace the indicated print cartridge, or press [Yes] to finish printing before replacing the indicated print cartridge.
What to do if copied pages do not look the same as the originals on my Kyocera FS-C1020MFP+ All in One Printer?
If copied pages do not look the same as the originals on your Kyocera All in One Printer, select the correct scan mode according to the type of original.
Why do black spots appear when photocopying a photographic print on my Kyocera FS-C1020MFP+?
If black spots appear when photocopying a photographic print on your Kyocera All in One Printer, the original may have stuck to the exposure glass due to high humidity. Place the original on the exposure glass, and then place two or three sheets of white paper on top of it. Leave the ADF open when copying.
Why prints do not stack properly from my Kyocera FS-C1020MFP+ All in One Printer?
If prints do not stack properly from your Kyocera All in One Printer, the paper might be damp, so use paper that has been stored properly. Select [Lvl.2: Medium] or [Lvl.3: Strong] in [Anti-Humidity Level] under [System Settings]. Pull up the appropriate stop fence (forward fence for A4/Letter, rear fence for Legal size prints).
What to do if my Kyocera FS-C1020MFP+ All in One Printer has a considerable delay between print start and actual printing?
If there is a considerable delay between the print start command and actual printing on your Kyocera All in One Printer, note that processing time depends on data volume; high volume data, such as graphics-heavy documents, take longer to process. If "Processing..." is displayed on the screen, the machine is receiving data, so wait for a while. To speed up printing, reduce the printing resolution using the printer driver. The machine might also be calibrating color; wait for a while.
General| Duplex printing | Yes |
|---|---|
| Print technology | Laser |
| Maximum resolution | 2400 x 600 DPI |
| Time to first page (black, normal) | 14 s |
| Print speed (black, normal quality, A4/US Letter) | 20 ppm |
| Digital sender | - |
| Printing colors | Black, Cyan, Magenta, Yellow |
| Maximum duty cycle | 65000 pages per month |
| Number of print cartridges | 4 |
| Page description languages | PCL 5c, PCL 6, PostScript 3 |
| Maximum copy resolution | 600 x 600 DPI |
| Maximum number of copies | 999 copies |
| Scan to | E-mail, File, FTP, Image, USB |
| Scan drivers | TWAIN, WIA |
| Maximum scan area | Legal (216 x 356) mm |
| Scan speed (black) | 12 inch/min |
| Scan speed (color) | 6 inch/min |
| Image formats supported | JPG, TIF |
| Document formats supported | |
| Optical scanning resolution | 1200 x 1200 DPI |
| Fax memory | 100 pages |
| Modem speed | 33.6 Kbit/s |
| Fax coding methods | JBIG, MH, MMR (Fax coding method), MR |
| Fax resolution (black) | 200 x 200 DPI |
| Fax transmission speed | 4 sec/page |
| Paper input type | Cassette, Paper tray, Sheetfed |
| Total input capacity | 286 sheets |
| Total output capacity | 150 sheets |
| Maximum input capacity | 768 sheets |
| Total number of input trays | 3 |
| Auto document feeder (ADF) input capacity | 35 sheets |
| Custom media width | 90 - 216 mm |
| Maximum print size | 216 x 356 mm |
| Custom media length | 148 - 356 mm |
| Duplex media weight | 60 - 90 g/m² |
| Paper tray media types | Plain paper |
| Paper tray media weight | 60 - 160 g/m² |
| Non-ISO print media sizes | Legal |
| ISO A-series sizes (A0...A9) | A4 |
| Auto Document Feeder (ADF) media weight | 52 - 105 g/m² |
| Display | LCD |
| Product color | Gray |
| Market positioning | Business |
| Display number of lines | 4 lines |
| Direct printing | No |
| Standard interfaces | Ethernet, USB 2.0 |
| Mobile printing technologies | Not supported |
| Processor family | ARM |
| Sound power level (standby) | 34 dB |
| Sound pressure level (copying) | 57 dB |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (PowerSave) | 10 W |
| Power consumption (average operating) | 381.9 W |
| Mac operating systems supported | Mac OS X 10.3 Panther, Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion |
| Server operating systems supported | Windows Server 2003, Windows Server 2003 x64, Windows Server 2008, Windows Server 2008 R2, Windows Server 2008 x64 |
| Windows operating systems supported | Windows 2000, Windows 2000 Professional, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64 |
| Sustainability certificates | ENERGY STAR |
Weight and Dimensions| Depth | 493 mm |
|---|---|
| Width | 420 mm |
| Height | 476 mm |
Provides steps for installing the machine and preparing it for use.
Explains the procedure for turning the machine on and important safety precautions.
Guides through the initial setup process for the machine upon first use.
Covers connecting the machine to a computer and a telephone line.
Covers configuring network settings for network and fax use.
Describes how to load paper into the paper tray and bypass tray.
Describes how to set paper size and type via the control panel.
Covers types of originals and how to place them for scanning.
Describes setting user codes to restrict access to certain functions.
Guides on configuring the printer driver for machine options and paper settings.
Explains the fundamental steps for performing printing operations.
Explains how to use the Locked Print function for secure printing.
Explains the fundamental steps for making photocopies.
Details how to set scaling ratios for enlargement or reduction.
Explains how to combine multiple original pages onto a single sheet.
Steps to copy dual-sided ID cards onto single-sided paper.
Instructions on setting up the machine for 2-sided copying.
How to adjust image density and quality for current scanning jobs.
How to register destinations for scan jobs in the Address Book.
Explains how to scan using the machine's control panel.
How to send scanned files to a USB flash disk.
How to specify scanning size, density, and resolution for the current job.
How to set the machine's internal clock and display format.
Explains how to register fax destinations in the Address Book.
Covers transmission modes and basic operations for sending faxes.
Details methods for specifying fax destinations.
Details how to use the fax function from a computer via LAN-Fax.
Covers fax reception functions and modes.
How to forward or store received faxes to prevent unauthorized access.
How to set the machine to receive or reject faxes from specific senders.
How to set the machine to receive faxes only from programmed Special Senders.
Step-by-step instructions for replacing print cartridges.
Instructions for replacing the waste toner bottle.
To Next Page