Kyocera KM-1650 - Specifications

2DA/2DB
1-1-1
1-1 Specif ications
1-1-1 Specifications
Type ................................................Desktop
Copying system ..............................Indirect electrostatic system
Originals..........................................Sheets, books and 3-dimensional objects (Maximum original size: A3/11" x 17")
Original feed system .......................Fixed
Copy paper .....................................Paper weights
Drawer: 60 - 105 g/m
2
Bypass table: 45 - 160 g/m
2
Paper type Drawer: Plain paper, recycled paper and colored paper
Bypass table: Plain paper, recycled paper, thin paper, thick paper and colored paper
Copying sizes .................................Maximum: A3/11" x 17"
Minimum: A6R /5
1/2" x 8 1/2"
Magnification ratios.........................Manual mode: 25 - 200%, 1% increments
Copy speed.....................................At 100% magnification in copy mode:
16 ppm model 20 ppm model
A4: 16 copies/min. A4: 20 copies/min.
A4R: 13 copies/min. A4R: 13 copies/min.
A3: 8 copies/min. A3: 10 copies/min.
A5R: 10 copies/min. A5R: 10 copies/min.
A6R: 10 copies/min. A6R: 10 copies/min.
B5: 16 copies/min. B5: 20 copies/min.
B5R: 13 copies/min. B5R: 13 copies/min.
B4 (257 x 364 mm): 8 copies/min. B4 (257 x364 mm): 11 copies/min.
11" x 8
1/2": 16 copies/min. 11" x8 1/2": 20 copies/min.
8
1/2" x 11": 13 copies/min. 8 1/2" x11": 13 copies/min.
11" x 17": 8 copies/min. 11" x17": 10 copies/min.
8 1/2" x14": 8 copies/min. 8 1/2" x 14": 11 copies/min.
First copy time ................................Approximately 5.9 s or less (A4/11" x 8
1/2")
Warm-up time .................................Less then 20 s (room temperature 23
°C/73.4°F, 50% RH)
Time for recovery from low power mode: 10 s
Time for recovery from sleep mode: 20 s
Paper feed system..........................Automatic feed
Capacity:
Drawers: 300 sheets (80 g/m
2
)
100 sheets (90 - 105 g/m
2
)
Manual feed
Capacity:
Bypass: 50 sheets (A4/11" x 8
1/2" or less)
25 sheets (A3, B4, 11" x 17", 8
1/2" x 14")
Paper ejection system ....................In-machine ejection (face down)
Capacity: 250 sheets (80 g/m
2
)
Continuous copying ........................1 - 999 sheets
Photoconductor...............................OPC (drum diameter 30 mm)
Charging system.............................Single positive corona charging
Recording system ...........................Semiconductor laser
Developing system .........................Single component developing system
Toner: magnetism toner
Toner replenishing: automatic from a toner container
Transfer system ..............................Transfer roller
Separation system ..........................Curvature separation and separation electrode
Fixing system..................................Heat roller
Heat source: halogen heaters (120 V specifications: main 550 W, sub 400W/ 220-240
V specifications: main 590 W, sub 430 W)
Control temperature: 170
°C/338°F (180°C/356°F on and after 6th sheet)
Abnormally high temperature protection device: 180
°C/356°F thermostat
Fixing pressure: 44.1 N
Charge erasing system...................Exposure by cleaning lamp
Cleaning system .............................Cleaning blade
Scanning system ............................Flat bed scanning by CCD image sensor
Bitmap memory...............................35 MB (standard)
Image storage memory...................29 MB (standard)