Kyocera KM-2020

2C9-3
1-1-1
1-1-1 Specifications
Type ............................................... Desktop
Copying system.............................. Indirect electrostatic system
Originals ......................................... Sheets, books and 3-dimensional objects (Maximum original size: A3)
Maximum size: A3/11" × 17"
Original feed system ...................... Fixed
Copy paper..................................... Paper weights
Drawer: 64 – 105 g/m
2
Bypass table: 45 – 160 g/m
2
Paper type
Drawer: Plain paper, recycled paper and colored paper
Bypass table: Plain paper, recycled paper, thin paper, thick paper and colored paper
Copying sizes ................................. Maximum: A3/11" × 17"
Minimum: A6R /5
1
/
2
" × 8
1
/
2
"
Magnification ratios ........................ Manual mode: 50 – 200%, 1% increments
Copy speed .................................... At 100% magnification in copy mode:
16cpm machine
A4: 16 copies/min.
A4R: 13 copies/min.
A3: 8 copies/min.
A5R: 10 copies/min.
A6R: 10 copies/min.
B5: 16 copies/min.
B5R: 13 copies/min.
B4 (257 × 364 mm): 8 copies/min.
11" × 8
1
/
2
": 16 copies/min.
8
1
/
2
" × 11": 10 copies/min.
11" × 17": 8 copies/min.
8
1
/
2
" × 14": 8 copies/min.
First copy time ................................ Approximately 5.9 s (A4/11" × 8
1
/
2
")
Warm-up time .................................
Less then 19.8 s (room temperature 20°C/68°F, 50% RH)
Paper feed system ......................... Automatic feed
Capacity:
Drawers: 300 sheets (80 g/m
2
)
Manual feed
Capacity:
Bypass: 50 sheets (A4/11" × 8
1
/
2
" or less)
25 sheets (A3, B4, 11" × 17", 8
1
/
2
" × 14")
Paper ejection system .................... In-machine ejection (face down)
Capacity: 250 sheets (80 g/m
2
)
Continuous copying........................ 1 – 250 sheets
Photoconductor .............................. OPC (drum diameter 30 mm)
Charging system ............................ Single positive corona charging
Recording system .......................... Semiconductor laser
Developing system ......................... Single component developing system
Toner: magnetism toner
Toner replenishing: automatic from a toner container
Transfer system ............................. Transfer roller
Separation system ......................... Curvature separation and separation electrode
Fixing system ................................. Heat roller
Heat source: halogen heaters (120 V specifications:main 550 W, sub 400W/ 220-240
V specifications:main 600 W, sub 450 W)
Control temperature: 170°C/338°F (180°C/356°F on and after 6th sheet)
Abnormally high temperature protection device: 180°C/356°F thermostat
Fixing pressure: 44.1 N
Charge erasing system .................. Exposure by cleaning lamp
Cleaning system............................. Cleaning blade
Scanning system ............................ Flat bed scanning by CCD image sensor
Bitmap memory .............................. 18 MB (standard)
Image storage memory .................. 14 MB (standard)
Resolution ...................................... 600 × 600 dpi
20cpm machine
A4: 20 copies/min.
A4R: 13 copies/min.
A3: 10 copies/min.
A5R: 10 copies/min.
A6R: 10 copies/min.
B5: 20 copies/min.
B5R: 13 copies/min.
B4 (257
× 364 mm): 11 copies/min.
11"
× 8
1
/
2
": 20 copies/min.
8
1
/
2
" × 11": 13 copies/min.
11"
× 17": 10 copies/min.
8
1
/
2
" × 14": 11 copies/min.